GE Appliances JGBS04 Owner's Manual And Installation Instructions page 29

GEAppliances.com
Burner cap is
properly seated.
NOT properly
seated.
Be!net heads !on s ome mode!s! }
The burner heads (on Some models)
are removable, Simply lift them Off {
the range for cleaning;
Tr!-ring head (on some me@!s)
Burner head (,%/_1,_.,:_- !
::: i]_]Tc ....
._) J Electrode
/i ...... _%F _ ,"
Burnei b ose _ C>o._'
Make Sure t hering]nthe burner head
ispositioned over t heelectrode and
that theburner head !sfully inserted
inside _ he burner base. Astnalt gap
between thebase and head isnormal.
Front-right head (on some models),
front-left head bacbright head and
back-left head
Stab lity chamber
Use ase_,4ng
_J_"_"t, needleor twist-tie
Bumer(k_ _ )) to unclogthe
• '_' _ smallholeinthe
bas e'''_ Electrode burnerhead.
Make sure the slot in the burner head
iSpositioned over the electrode,
Hole in
head
The oval b urnei head/caP assembly is
remavablel Simply liftitOffthe r ange for
cleaning_ Use asewing n eedle ortwist-tie
tounclog t hesma!! hole intheburner
heads,
Burner Caps, Bases and Heads
Before removing the burner caps and heads
(on some models), remember their size and
location. Replace them in the same location
after cleaning.
NOTE: Do not use steel wool or scouring
powders to clean the burner parts.
Burner caps
Lift off when cool. Wash burner caps in hot,
soapy water and rinse with clean water. You
may scour with a plastic scouring pad to
remove burned-on food particles.
Tri-ring burner (onsome models)
The outer cap on the tri-ring burner is not
removable. Only the center round cap may be
removed for cleaning.
To cleanthe burner bases,usesoapywater and a
plasticscouringpad.Wipecleanwith a damp cloth.
Hake sure that no water gets into the burner
bases.Allow them to dry fully before using.
Burner Heads (on some models) and Oval
(Center) Burner Heed/Cup Assembly
The burner heads and the oval burner head/cap
assembly are removable.Simply lift them off the
range for cleaning.
For proper ignition, make sure the small hole in
the section that fits over the electrode is kept
open. A sewing needle or wire twist-tie works
well to unclog it.
The slits in the burner heads must be kept clean
at all times for an even, unhampered flame.
Clogged or dirty burner ports or electrodes will
not allow the burner to operate properly.
Any spill on or around an electrode must
be carefully cleaned. Take care to not hit an
electrode with anything hard or it could be
damaged.
Clean the burner heads routinely, especially
after bad spillovers, which could clog the
openings. Liftoff when cool.
To remove burned-on food, soak the burner
heads in a solution of mild liquid detergent
and hot water for 20-30 minutes. For more
stubborn stains, use a toothbrush.
After cleaning
Before putting the burner caps, heads (on some
models) and oval head/cap assembly back,
shake out excess water and then dry them
thoroughly by setting in a warm oven for 30
minutes.
Replacement Burner Heads (on some models)
Replace burner heads over the electrodes on
the cooktop, in the correct locations according
to their size.There is one small, one medium,
one large and one extra-large burner head.
0
®
"_ront o_ range _
_onsome modem
Tn-nnghead
Makesurethe sot or no_edepending on moae__
me ournerhead is positioned overthe electrode.
Or ..... C
__-Sb i _/Electrode
Electrode
Oval (Cented Burner Head/Cap 4ssernbly
ReD,ace m e ova center) neaa/capassemD,y o ver
me electrodeon me COOKtOp.
Oval head and CaD
ass qoiy
®
Make sure the slot in tne
ourner head is aos_oned
over me electrode.
Front of ranoe Electrode
Caps
Realace the matchingsizecapsontome Durner
Doses or heads.
Makesurethat the heads on some moae,sanc
caps are rep,acea in me correc_ ioca_,ons
0
O Omodel s
:rant of range Trl-nng CaD
0
on some
models
29