Serial Terminals Connection - Panasonic TH-65PB1E Operating Instructions Manual

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Note: To use serial control for this unit, make sure to set the "Control I/F Select" in the "Network Setup" menu to
"RS-232C". (refer to "Operating Instructions, Network Operations")
COMPUTER
Notes:
• Use the RS-232C straight cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface
speci¿ cation, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the
sending and receiving of control data which satisfies
the conditions given below. Use a computer application
such as programming language software. Refer to the
documentation for the computer application for details.
Communication parameters
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command, the
parameters, and lastly an ETX signal in that order. If there
are no parameters, then the parameter signal does not
need to be sent.
STX C1 C2 C3 :
Colon
Start 3-character
(02h) command (3 bytes)
Notes:
• If multiple commands are transmitted, be sure to wait for
the response for the ¿ rst command to come from this unit
before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an "ER401" command back to the computer.
• S1A and S1B of Command IMS are available only when
a dual input terminal board is attached.
• Consult your local Panasonic dealer for detail instructions
on command usage.
14
RS-232C Straight cable
D-sub 9p
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
P1 P2 P3 P4 P5 ETX
Parameter(s) End
(1 - 5 bytes) (03h)
(Male)
(Female)
Signal names for D-sub 9P connector
Pin No.
4 • 6
1 • 9
These signal names are those of computer speci¿ cations.
Command
Command
PON
POF
AVL
AMT
IMS
DAM
With the power off, this display responds to PON command
only.
(8Ω,20W[10W+10W])
9
5
Pin layout for SERIAL Terminal
2
3
5
7
(Shorted in this set)
8
Parameter Control details
None Power ON
None Power OFF
** Volume 00 - 63
0 Audio MUTE OFF
1 Audio MUTE ON
None Input select (toggle)
SL1 SLOT input (SLOT INPUT)
S1A SLOT input (SLOT INPUT A)
S1B SLOT input (SLOT INPUT B)
VD1 VIDEO input (VIDEO)
YP1 COMPONENT/RGB IN input
(COMPONENT)
HM1 HDMI input (HDMI)
DV1 DVI-D IN input (DVI)
PC1 PC IN input (PC)
NW1 Network input (NETWORK)
None Screen mode select (toggle)
ZOOM Zoom, Zoom1
FULL 16:9
JUST Just, Just1 (For Video/SD/HD signal)
NORM 4:3, 4:3 (1)
ZOM2 Zoom2 (For Video/SD/HD signal)
ZOM3 Zoom3 (For Video/SD/HD signal)
SJST Just2 (For HD signal)
SNOM 4:3 (2) (For HD signal)
SFUL 4:3 Full (For HD signal)
14:9 14:9 (For Video/SD/HD signal)
8 7 6
4 3 2 1
Details
R X D
T X D
GND
Non use
NC