Subwoofer Output - Marantz SR-14mkII User Manual

13 Three Component-video inputs
DVD,VCR1,DSS :
Connect the Y/Cr/Cb component video outputs of each your video
product to these jacks.
14 Component Video Outputs
Connect these outputs to the component video inputs of a video
projector or monitor. When a source connected to one of the three
Component Video Inputs is selected the signal will be sent to these
jacks.
15 Multiroom Outputs (Audio L&R, Video)
Connect these jacks to the optional audio power amplifiers or video
display devices to view and listen to the source selected by the
mulitroom system in a remote room.
16 Main Amplifier Inputs:
When the jumper pins that link the Preamp Outputs with these
inputs are removed, these jacks may be used to connect an external
source to the internal amplifiers.
Front L/R and (Front L/R) are connected internally. If you desire to
use internal the 2ch amplifiers of the front L/R channels for the
surround back L & R channel, you may remove the jumper pins for
front L/R channels, and then connect between (Front L) and
preoutput of Surr Back L channel, (Front R) and preoutput of Surr
Back R channel.
An external 2channel amplifier may be connected to the preoutput of
the Front L&R channels.
(See page IIi.)
17 Preamp Outputs( L,R,SL,SR,SBL,SBR,C )
When the jumper pins that link the Amplifier Inputs with these
outputs are removed, these jacks may be connected to an external
power amplifier.

18 Subwoofer Output

Connect this jack to the line level input of a powered subwoofer. If an
external subwoofer amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two subwoofers, either
powered or with a 2 channel subwoofer amplifier, connect a "Y"
connector to the subwoofer output jack and run one cable from it to
each subwoofer amplifier.
19 Five Digital Inputs ( Dig. 1 – 5)
Dig.1,2,3 (Optical), Dig.4,5(Coaxial):
Connect the digital output from a DVD player, HDTV receiver, LD
player or CD player to these jacks. The signal may be either a Dolby
Digital signal, DTS signal or a standard PCM digital source.
20 Digital 6(AC-3 RF or Coaxial ) Input
Connect the AC-3RF output from a LD player and select RF in the
OSD system setup menu. If you don't need an AC3RF input, select
COAXIAL in the OSD system setup menu and this terminal will be
useable for a coaxial digital input.
(See page 18 "System setup 1/2".)
21 Digital Audio Outputs (Optical, Coaxial)
Connect these jacks to the matching digital input connector on a
digital recorder such as a CD-R or Mini Disc recorder.
22 Speaker outputs terminals
Front L, Front R, Surround L, Surround R and Center:
Connect the these jacks to the matching + or – terminals on your
speakers. When making speaker connections, always make certain
to maintain correct polarity by connecting the red (+) terminals on the
SR-14mkII to the red terminals on the speaker and the black (–)
terminals on the SR-14mkII to the black terminals on the speakers.
These terminals will accept bare wire or pin connectors. Additionally,
your dealer can remove the center plastic "plugs" for you and the
terminals will then accept banana plugs as well.
23 Remote control In/Out terminals
INPUT: This connection permits the IR sensor in the receiver to
serve other remote controlled devices.
Connect this jack to the "IR IN (RC-5 in)" jack on Marantz or
other compatible equipment.
OUTPUT: If the SR-14mkII's front-panel IR sensor is blocked due to
cabinet doors or other obstructions, an external IR sensor
may be used. Connect the output of the sensor to this jack.
24 MULTI ROOM Remote In/Out terminals
Connect to multi-room remote control device, available from
IN:
your Marantz dealer.
OUT: Connect to the Marantz component equipped with remote
control (RC-5) terminals in another room .(Second zone).
25 AC INLET
Connect the provided detachable power cord, and connect the AC
plug to an unswitched AC wall output.
9