Scag Power Equipment STC48V-19KAI Operator's Manual page 43

Section 8
Ref.
Part No. Description
No.
1 461854 Cutter Deck Velocity Plus
2 43686 Boss, Spring Anchor
3 04019-04 Nut, 3/8-16 Serrated Flange
4 481625-01 Wing Nut, 3/8-16
5 481632 Anti-Scalp Wheel
6 04003-26 Bolt, Carriage 3/8-16 x 4"
7 422478 Bracket, Anti-Scalp Wheel
8 04017-27 Bolt, Serrated Flange 3/8-16 x 1"
9 04043-06 Flatwasher, 5/8" Hardened
10 04021-05 Locknut, 3/8-16 Center Lock
11 461844 Discharge Chute
12 04001-11 Bolt, Hex Head 5/16-18 x 1-1/2", Rear
04001-12 Bolt, Hex Head 5/16-18 x 1-3/4", Front
13 04021-10 Nut, Elastic Stop 5/16-18
14 04020-09 Nut, 5/8-11 UNC
15 45944 Shaft, Roller
16 04001-41 Bolt, Hex Head 5/8-11 x 9-1/2"
17 48038 Roller, Rear
18 04001-154 Bolt, Hex Head 5/16-18 x 4-3/4"
19 04063-08 Key, 1/4 x 1/4 x 2"
20 483246 Spring, Idler LH
21 04043-04 Flatwasher, 3/8"
22 04001-176 Bolt, Hex Head 5/16-18 x 1-3/4" Grade 8
23 04019-03 Nut, Serrated Flange 5/16-18
24 04001-51 Bolt, Hex Head 3/8-16 x 3-3/4"
25 48100-15 Bushing, .376 ID Oilite
26 04030-03 Lockwasher 5/16"
27 04040-15 Flatwasher 5/16"
28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2" Gr. 8
29 04021-09 Nut, Elastic Stop 3/8-16
30 04001-31 Bolt, Hex Head 3/8-16 x 2-1/2"
31 483247 Spring, Idler RH
32 424369 Bracket, Spring Anchor LH 48V
33 04110-03 U-Nut, 3/8-16
34 461663 Spindle Assembly
35 43589 Shaft, Spindle
36 481024 Seal, Upper
37 481022 Bearing Assembly
38 48114-04 Grease Fitting
39 48677 Valve, Grease Relief
40 43644 Housing, Spindle
41 43312 Spacer, Outside
42 43296 Spacer, Inside
43 481025 Seal, Lower
44 43297 Bushing, Bottom
45 481035 Nut, Special 1-1/16 - 18
46 43590 Spacer, Spindle
47 482877 Cutter Blade 16.5"
48 483210 Pulley, Idler 5" Dia.
49 48224 Bearing
50 461940 Idler Arm Assy.
48v Cutter Deck
Ref.
Part No.
No.
51 43689
52 424322
53 48926
54 461946
55 04001-172
56 483282
57 424208
58 451240
59 461516
60 04020-16
61 04021-13
62 48763
63 04001-79
64 48114-04
65 483241
66 04001-09
67 483378
68 424839
04003-23
70 04021-22
71 04043-04
72 483239
73 48181
74 483283
75 483167
76 461929
77 04003-40
78 04040-11
79 04021-11
80 424367
81 04030-03
82 424376
83 04001-136
84 04001-19
85 04021-04
86 483176
87 43689
88 04003-12
89 04040-04
39
Description
Idler Pivot
Belt Cover (48V)
Hub, Tapered 1-1/8" Bore
Idler Arm
Bolt, Hex Head 1/4-20 x 1" Grade 8
Pulley 4.75"
Turbo Baffle, Bolt On
Push Arm Shaft
Push Arm (Includes 64,60,62)
Nut, 5/8-18 UNF
Nut, Elastic Stop 5/8-11
Rod End, 5/8 Male RH Thread
Bolt, Hex Head 5/8-11 x 4-1/2"
Grease Fitting, 90 Degree
Belt, Cutter Deck Drive (48V)
Bolt, Hex Head 5/16-18 x 1"
Spring, Discharge Chute
Baffle Weldment, 48V
Bolt, Carriage 3/8-16 x 1"
Nut, Elastic Stop 5/16-18 Grade 8
Flatwasher 3/8"
Belt, RH Cutter Deck
Pulley, Idler 5" Dia.
Pulley, Double Groove
Bolt, Special
Lever Assy., Deck Level
Bolt, Carriage 7/16-14 x 1-1/4"
Flatwasher, 7/16-.500 x 1.25 x .083
Nut, Elastic Stop 7/16-14
Dust Shield
Lockwasher 3/8"
Bracket, Spring Anchor RH
Bolt, Hex Head 3/8-16 x 1-1/2" Gr. 8
Bolt, Hex Head 3/8-16 x 1"
Nut, Center Lock 5/16-18
Wear Pad
Idler Pivot
Bolt, Carriage 5/16-18 x 3/4"
Flatwasher, 5/16"
R