Manual Equalizer Control; Dual Zone System - Kenwood KDC-BT92SD Instruction Manual

Audio Adjustments

Manual Equalizer Control

You can adjust following Equalizer Control items.
Band Item Range
"BAND1" (62.5 Hz) "GAIN" Band level -9 –+9 dB
"B.Ex" Bass Effect "ON"/ "OFF"
"BAND2" (100 Hz) "GAIN" Band level -9 –+9 dB
"BAND3" (160 Hz) "GAIN" Band level -9 –+9 dB
"BAND4" (250 Hz) "GAIN" Band level -9 –+9 dB
"BAND5" (400 Hz) "GAIN" Band level -9 –+9 dB
"BAND6" (630 Hz) "GAIN" Band level -9 –+9 dB
"BAND7" (1 kHz) "GAIN" Band level -9 –+9 dB
"BAND8" (1.6 kHz) "GAIN" Band level -9 –+9 dB
"BAND9" (2.5 kHz) "GAIN" Band level -9 –+9 dB
"BAND10" (4 kHz) "GAIN" Band level -9 –+9 dB
"BAND11" (6.3 kHz) "GAIN" Band level -9 –+9 dB
"BAND12" (10 kHz) "GAIN" Band level -9 –+9 dB
"BAND13" (16kHz) "GAIN" Band level -9 –+9 dB
1.35/ 1.5/ 2.0
"BAND1" – "BAND13" "Q" Quality
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than "STANDBY".
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter Manual Equalizer Control mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Manual Equalizer".
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
6
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• When "iPod" is selected in the section <Preset Equalizer
curve Select> (page 44), Manual Equalizer Control is
disabled.
• You can select for each source.
45
|
KDC-BT92SD

Dual Zone System

Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
Display Overview
"2 Zone" Sets the Dual Zone System.
"OFF"/ "ON"
"2 Zone Rear Volume"* Adjust the volume of Rear channel.
"0" — "35"
"2 Zone Select"* Specifies the destination of sub source sound
when the Dual Zone function is turned on.
"Rear"/ "Front"
* The Dual Zone System is set to "ON".
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than "STANDBY".
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Pro Setup" > "Zone Control".
4
Select the item you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• Select Main source by [SRC] button.
• Adjust the volume of Front channel by [VOL] knob.
• The Audio Control has no effect on sub source.
• There are following limitations when Dual Zone System
is enabled.
- There is no output from the subwoofer.
- "Fader", "Subwoofer Level" of <Audio Control> (page 43)
and DSP function are not available.
• The Bluetooth audio source can be set exclusively to the
front speaker. Set "2Zone Select" to "Rear".
46
|
English