Channel Select - Fender 100H Owner's Manual

6
Your new FM 100H amplifier delivers world–class Fender
tone and world–standard Fender
• 100W output power into 4 ohms
• Selectable Normal
independent volume and tone controls
• MORE DRIVE pre-amp boost for instant gain saturation
and harmonically rich leads
• MID-CONTOUR button allows for many different
variations in distortion—from Rock to Blues to Metal to
whatever!
• Classic Fender ® spring Reverb
NOTE: The footswitch and power cord are stored behind the front grille of the FM100H cabinet. Access by pulling on
both tabs at the bottom edge of the grille.
1 2
INPUTS
VOLUME TREBLE
A. INPUTS - Plug your guitar in here: INPUT 1 is normal
sensitivity for most guitars, INPUT 2 is lower sensitivity
for guitars with high output (active) pickups.
B. VOLUME - Adjusts the loudness of the Normal
channel.
C. TREBLE/MID/BASS - Adjusts the tone of the Normal
channel in the high/middle/low frequency ranges.
D. DRIVE CHANNEL INDICATORS -
Yellow LED ON Drive channel is active
Red LED ON More Drive channel is active
E. DRIVE - Adjusts the distortion level of the Drive
channel.
F. CHANNEL SELECT -
Button OUT selects the Normal channel
Button IN selects the Drive channel
G. VOLUME - Adjusts the loudness of the Drive channel
together with DRIVE {E}.
H. MORE DRIVE - Boosts the intensity and range of the
DRIVE control {E}.
Button OUT selects the Drive channel
Button IN selects the More Drive channel
I. TREBLE/MID/BASS - Adjusts the tone of the Drive
channel in the high/middle/low frequency ranges.
F F M M 1 1
F F M M 1 1
® quality:
and Drive channels
F F
F F
CH SELECT MORE DRIVE
MID BASS DRIVE VOLUME
f f e e n n d
0 0 0 0 H H A A m m p p l l i i f f i i e e r r
0 0 0 0 H H A A m m p p l l i i f f i i e e r r
® • Fender ® "touch-sensitive" circuit design simulates the
feel of tube distortion
• PRE-AMP OUT and POWER-AMP IN jacks allow you to
connect external effects devices, other amplifiers or
with
sound/recording equipment to your FM 100H
• FOOTSWITCH jack for use with a 2-button Fender
footswitch (included).
channel selection and drive/more drive switching
Thank you for choosing Fender
Thank you for choosing Fender
popular instr ument amplifiers—since 1946
popular instr ument amplifiers—since 1946
r r o o n n t t P P a a n n e e l l
r r o o n n t t P P a a n n e e l l
MID
CONTOUR
TREBLE MID BASS REVERB
J. MID-CONTOUR - Activates a "scooped" midrange
EQ, useful for modern distortion sounds in the Drive
channel.
K. REVERB - Adjusts the Reverb level for both channels.
L. FOOTSWITCH - Plug in the included 2-button Fender
footswitch to enable remote switching of CH SELECT,
and DRIVE/MORE DRIVE.
footswitch overrides the front panel buttons.
M. PRE OUT/PWR IN - (1) Effects Loop - Connect PRE
OUT to an effects device input, then connect the
effects device output to PWR IN. (2) Multiple Amps -
Connect the primary amplifier's PRE OUT to the
auxiliary amplifier's PWR IN. The primary amp is used
to control all auxiliary amps. (3) Recording or
Reinforcement - Connect PRE OUT to sound
equipment's input.
Both jacks use a TS (Tip-Sleeve) standard type
plug for connections. PRE OUT includes onboard tone
shaping.
N. POWER INDICATOR - Illuminates when the amplifier
is on.
d e e r r . . c c o o m m
A footswitch provides remote
—The W
® ® —The W
FOOT PRE PWR
SWITCH OUT IN
When connected, the
®
orld' s most
orld' s most
F E N D E R M U S I C A L I N S T R U M E N T S
®