Operating Position - Weed Eater TE400 LE Instruction Manual

OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
ALWAYS WEAR: _[_'_ Eye
Protection
Long Pants _ "_
Heavy Shoes -_L
CL_ from your right to your left.
_ WARNING:
Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cL_ting line will CL_ efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to "weld" onto the spool
Always release the throttle trigger and allow the
engine to return to idle speed when not cL_ting.
TO stop engine:
• Release the throttle trigger.
• Move the ON/OFF switch to the OFF
position.
TWIST AND EDGE
The Twist and Edge feature allows for easy
edging of sidewalks, patios, driveways, etc.
1. Pull the tab toward the engine.
2. Twist the tube to the edging position; re-
lease tab.
• Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2
inches (5 cm) of line will be advanced with
each tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
_WARNING:
Use only 0.080" (2 mm)
diameter line. Other sizes and shapes of line
will not advance properly and will result in im-
proper cutting head function or can cause se-
rious injury. Do not use other materials such
as wire, string, rope, etc. Wire can break off
during cutting and become a dangerous mis-
sile that can cause serious injury.
CUTTING METHODS
_WARNING: Use minimumspeed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
• The tip of the line does the cutting, You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area. The right and wrong
ways are shown below.
Tip of the Line i
D oei The Cutting
Line Crowded Into
Work Area
W
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 am) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter. Always keep
the shield in place when the tool is being oper-
ated.
To advance line:
• Operate the engine at full throttle.
• Hold the trimmer head parallel to and above
the grassy area.
• The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4-5 in. (10-13 cm) and use
at less than full throttle.
• For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
• During light duty cutting.
• Near objects around which the line can
wrap such as small posts, trees or fence
wire.
• For mowing or sweeping, use full throttle for
a good clean job.
TRIMMING - Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
6