Weed Eater TE400 LE Instruction Manual page 3

Electrolux
Hide thumbs Also See for TE400 LE:
Table of Contents

Advertisement

Available languages

Available languages

• Always
store gasoline
in a container
ap-
proved for flammable
liquids.
CUTTING
SAFETY
_;_,WARNING:
Inspect the area before
each use.
Remove objects
(rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage
trimmer
head and be thrown
causing serious injury.
• Use only for trimming, mowing, edging and
sweeping.
Donor usefor
pruningorhedge
trimming.
• Keep firm footing and balance. Do not over-
reach.
• Keep all parts of your body away from spin-
ning line and muffler. Keep engine belowwaist
level. A hot muffler can cause serious bums.
• CL_ting with the line on left side of the shield
will throw debris away from the operator.
• Use only in daylight or good artificial light.
TRANSPORTING
AND STORAGE
• Allow the engine to cool; secure unit before
storing or transporting
in vehicle.
• Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
• Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from
water
heaters,
electric
motors
or
switches, furnaces,
etc.
• Store unit so line limiter blade cannot acci-
dentally cause injury. Unit can be hung by
the tube.
_WARNING:
If received
assembled,
• Store the unit out of the reach of children.
SAFETY
NOTICE:
Exposure to vibrations
through prolonged
use of gasoline powered
hand tools could cause blood vessel or nerve
damage
in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings.
Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people.
If symptoms occur
such as numbness,
pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti-vibration
system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tooL
SPECIAL
NOTICE:
This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen,
if you operate in a Iocole where such
regulations exist, you are legally responsible for
maintaining the operating condition
of these
parts. Failure to do so is a violafion of the law.
For normal homeowner
use, the muffler and
spark arresting screen will not require any ser-
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your au-
thorized service dealer.
repeat all steps to ensure your unit is properly
assembled
and all fasteners are secure.
Examine
parts for damage. Do not use dam-
aged parts.
NOTE:
If you need assistance
or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to ratfie in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor
adjustments
and testing
done by the manufacturer.
ATTACHING
THE HANDLE
NOTE:
Be sure to attach the assist handle to
the unit before attaching the shield,
1. Assemble
handle to the unit as shown;
make sure bottom of handle is seated in
the groove in the trigger housing.
3
NOTE:
Knob must be assembled
on the
right hand side of the unit as shown in the il-
lustration.
2.
Make sure the bolt is seated in the hex-
shaped hole in the handle.
3. Pivot the handle to a comfortable position.
4. Tighten knob securely.
ATTACHING
SHIELD
WARNING:
The shield must be prop-
erly
installed.
The shield
provides
partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line to
the proper length. The line limiter blade (on
underside of shield) is sharp and can cut you.
For proper orientation
of shield, see KNOW
YOUR TRIMMER illustration
in OPERATION
section.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents