Sharp Aquos LC-70LE734U Operation Manual page 59

Using a PC
[] Command table
• Commands not indicated here are not guaranteedto operate.
CONTROL ITEM COMMAND PARAMETER
POWERONOOMMANDSETIING RiSiPiW 0i ! ! Off
i i i 1 i i i Or,[RS 2320]
2 i i i On [IP]
POWERSE_MG PiOiWiR oi i i P .... off
j j j lj j j P.... On
INPU• SELECTION TL_-'GGLE_ I iTiv iDI i • i G i D 0i i ix i i i (Toggb)
P
l iAiViD *i i i I:HDMI1,2:MDMI2,3:MDIV_I3,4:MDMI4.
i i i i i i 5: OOMPONEN]] 6:VIDEO 1.7:VIDEO 2
AV MODE BELEOT_ON Ai ViMiD * i i i 0:Crogg_e), 1:BTANDARD, _:MOWE, S: G AME.
i i i i i i 4: USER, 5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC.
i i i i i i 8:x.v.Oolor. 10g:AUTO
VOLUME V i O i L i M * i * i i Volume {O_60)
POSITION H-POSmON H i P i O i S * i * i * i
V PosmoN V 11P 110 11S * 11* 11* 11
CLOCK CII L llC IIK * i * i * i Only PC n]ode. (0 180)
PHASE P i H i S i E * i * i * i Only PC mode. (0 40)
VIEWMODE WiliDiE *i i i 0:(Toggle)[AV],l:SideBa/(AV),2:S.St/etch[AV]
i i i i i i 3: Zoom [AV], 4: Stretch [AV}, 5: No/real [PC]
i i i i i i 6: Zoom [PC], 7: Stretch [PC],
i i i i i i 8: Dot by Dot [PC} [AV], 9: Full Screen [AV]
i i i i i i 10:Auto [USB Video, DLNA Video orlnternet applications],
ii ii iI ii ii iI 11: Original [USB Video, DLNA Vid.... Interrlet applications]
i i i
MUTE MIUITIE *i i i 0: {Tcxjgle), 1 : On. 2: Off
SURROUND A i C i S i U * i i i 0:(Toggb), 1: On. 2: Off
AUDIO SELEC•ION A IiO IiH IiA x Ii i i {Toggle)
SLEEPTIMER OIFITIM *i i i 0:Off, I:OEFTIMER 30MIN,2:OEFTIMER 60MIN,
', ', ', ', ', ', 3: OFF TIMER 90 MIN, 4: OFF TIMER 120 MIN
CHAMNEL DIREC•DIOICIM nin i* i •hec,annelnu,nbe, olSV
CHANNEL i i i i i i {1 135)
(ANALOG) ', ', ', ', ', ',
DIRECT DI A 12 ip n in i* i* /01009999)
CHANNEL DICI21U n,n,*, (1999)
(DIGITAL) i i i
DiOi2iL n
DICI1; ; ;JO nini*i* (09999)
DiCil il nini*i* (06383)
CHUP OIHIUIP Xl i i Tl_echannelnumberofTV+l
CHDOWN CiHiDiW xi i i ThechannelnumberofTV 1
CO CiLiCiP xl i i {Toggb)
DEVICENAME TIVINIM, , , li i i
MODEL NAME M i N i RID 1 i i i
SOFTWARE VERSION SiWiViN li i i
IP PROTOCOL VERSION liPiPiV li i i
CONTROL CONTENTS
The Power On command rejected.
The Power On command accepted.
The Power On command accepted.
When the power is in standby mode, commands also go to waiting status
and so power consumption is just about the same as usual. W_th the
commands in waiting status, the Center Icon Illumination on the front of the
TV lights up.
it sh_lts to standby.
Power On
it input switches by the toggle. (It is the same as an input change key)
it input switches to %/. (A channel remains as it is. (Last memory))
Although it can choose now, it is toggle operation in inside.
The screen position variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position setting screen.
0: Although it can choose now, _t is toggle operation in inside.
1 : Only availabb when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input.
[AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
10.11 : Availabb when USB_Video. DLNA Video or Internet application is used.
An input change is included if it is not %/display.
In Air. _69ch is eflectEve.
In Cable, 1 135ch is effective.
DIGITAL Air (Two Part numbers, 2 digit plus 2 digit)
DIGITAL Cable (Two Part numbers. 3 digit plus 3 digtt)
Front half d DiGiTAL CABLE CHANNEL NO. (Designate major channel)
DIGITAL Cable (Two Part numbers, 3 dig_t plus 3 digit)
Rear half d DiGiTAL CABLE CHANNEL NO. (Designate minor channel)
DIGITAL Cable (One Part numbers, 5 digit, less than 10,(}{)0/
DiGiTAL Cable (One Part numbers, 5 digit, more than 10.000)
If it is not %/display, it will input switch to TV. (same function as CHA)
If it is not %/display, it will input switch to TV. (same function as CHV)
Tcxjgle operation of a closed caption.
The device name set in 'IP Control Setup" is displayed.
The model name of the TV
The current version of the TV sotcware is displayed.
The currently supported version d IP protocol is displayed.
If an underbar (_)appears in the parameter column, enter a space.
= If an asterisk (*)appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
= Any numerical value can replace the "x" on the table.
@- 58