Table of Contents
Advertisement
Buttons
don't work
•
The front panel
controls
may be locked
(disabled).
Use the remote
control
to unlock
the front
panel
controls
by
selecting
tile/:rot_//'c{_(_,l
i#ocb in tile Pm>t_tcA ctn_/rol
menu
and press
OK to unclleck
tile box.
•
Unplug
tile TV for ten minutes
and then plug
it back
in. Turn
tile TV on and try again.
TV turns off unexpectedly
•
Sleep timer may have been activatc(I. Go to page 33 for instructions.
•
Electronic protection
circuit may have been activated because
of a l)o\\-cr surge. W;dt 30 seconds
and then turn on
again. If this happens
flequently,
the voltage in your house may be abnormally
high or low.
,,
Unplug. \V;At ten minutes. Plug in again.
TV turns on unexpectedly
•
\Wukc up timer might have been activated. Go to [)age 33 for instructions.
Can't select
certain
channel
•
Channel may be blocked
or not approved
in the l'mwllgi/6b,(troLs
menu.
,*
If using a VCR, check to make sure the TViVCR button on tile VCR is in the correct mode (press the TViVCR button
on your VCR).
•
Press the ANTENNA button and then try to change channels.
Noisy stereo reception
•
May be a weak station. Use ,Shined mem_ to choose mono sound.
Volume buttons
not adjusting
volume louder
®
Check to make sure volume isn't ]imitc(I by the maximum
volume fcatun'.
Go to page 32 for more instructions.
Black box appears
on the screen
•
Closed-captioning
might bc on. Check
CTosud C?lp/ioJl in the &,/zp menu.
Go to page
31 for more
instructions.
TV picture
keeps switching
between
screen
formats
abruptly
,,
Switch
the Az(/omg(ti£/brmg(t
feature
ore See l)agc 29 for more
information.
Problems
with
HDMI/DV!
Connection
-
Make sure the H1)MI or DVI device is turned on and tile canes are firmly connected.
If problems
still occur, turn ()ft
your device. Re-connect
your device. Reset tile power by unplugging
tile power cord and plugging it back in.
,*
If you are tuned to the HDMIiDVI input and you're receiving
U_z_lsglbh, 5 (q,(al message on-screen,
press the
INFO button on tile remote. If AcqzAri,z 2 CT_a_z,_el a ppears
in tile channel banner, tile HI)MI or I)VI device isn't
responding.
Contact the manufacturer
of the HDMI or I)VI device for further assistance.
•
If you tune to the HDMIiDVI input and you see snow, the video goes in and out, or the video takes a long time to
appear, your HDMI or DVI device is having trouble sending vk/eo information
to the T\(. Re-connect
your device.
Reset the power by unplugging
tile power cord and plugging it back in. If problems
persist, try connecting
tile Y Pb
Pr jacks instead if they are avatab]e
or contact the manufi_cturer of tile HDMI or I)VI device for further assistance.
•
If you have black bars on each side of your picture, the device you connected
might have a switch or a menu
option allowing you to change the picture quality output that will fix this. Choose either 720p or 10S0i.
®
48@ signals aren't supported
by tile HI)MIiI)VI
input.
C'hapter4
1665105Bindb
36
4_
2/I7/06
6:31:58PM
Advertisement
Table of Contents
