Table of Contents
Advertisement
_
_ !i!_ _!_, !_ _!!_i!! i_ _!_!_ !i__!_i_ i !!i!,z!!! __ i!!_i_ i !!_!!!!i_!_!_
_!i!_z_i!
!_!!!!!!!_
i!¸i_i_i!_!
_!ii_ii!!!!_!i !!i!_i_i !!i!!!!_!!i!iiiiiii_!_
!!iiii_i_!!
!!_!iiii!_!_!
_ iiiiiiii_!_!
!iiiiiiii_ !!i!iiiii!_!_
!iii!ii!iii_i
i!i!i!i!i!i_iz!_i
!!i!i! _ _:_
__:__ _ __z_:_ __ _ _
_ _
__ _ _ _ _
_
_ _ _ _ _ _ _
_¸_i_iiiii_i_ _z_ i _iiiiiii!iiiii_ii_iiiiiii_i_i_iii_iii_i_i_i_iiii_i_i_
iiii_i_i_i_i_i_i_iiiiiiiiii_i_i_iil
_iiiiiii_iiiii _iiiiii_iiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiii i iiiiiiiiiiiiiiiiiiiiiiiiiiiii i iiiii iiiiiiiii_ii i iii_iiiiiiiiiiiiiii _ i i ii_i iiiiii!iiiiiiiiiiiiii_!iiiii!iiiii!ii!iiiiiii!iiiii i i_ iiiiii_iiiii_iiiii_i iiii_iiii_ii
i_ iiii_iii _iii_ii_iiii_ii
_ii_
i i_i ii_ i_iiiil _iiii_iii_i_i_i_i_i_i_ii_i_i_iii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i
_
_i_'_'_
_'__i_'_'_'_ _ii_
Connect the AM loop antenna.
/,_
Connect
the right (R) and left (L) speaker
1. Attach
the antenna
holder
to the rear
panel
of the
"7'
cables.
tuner/sound
processor.
2. Clamp the AM loop antenna
to the antenna
holder and
connect the antenna
terminal
to the rear panel of the
tuner/sound
processor.
3. Position the loop for the best reception.
Antenna holder
Press in until you hear a click.
AM loop antenna
Press hard enough to get it
fixed firmly in the place,
with a click.
You may attach the AM antenna
holder with a screw (in-
cluded) to a rack or other structure.
In this case, attach as
shown in _
-- -- Rack or other structure
To minimize
noise pickup, keep the AM loop antenna cord
along the heat outlet grille, and away from the flat cables.
• Be sure to connect speaker cables before connecting
the
AC power supply cord.
eThe load impedance of any speaker used with this unit must
be 6-8£_.
• Match the two wires from the left and right speaker cables
with the same colored levers of the speaker terminals, then
insert the wires into the respective terminals.
1. Strip off the outer
covering, and twist
=_====,,
_),
the center conductor.
15mm
2.
Make sure the bare ends of the wires are not unravelled.
(If they are, twist them tight again.) I'_
(For SC-CH717)
I I_--_]
Insert the wire to the rear panel
.._11_
I
_
of the speakers, and then pull _
I
down the lever.
_
"'J
(For SC-CH515)
Q Tilt the lever back
and insert the wire.
(_ Close the lever and
pull the cord gently
to be sure that it is
secured.
3. Insert the wire to the
rear panel of the
amplifier, and close the lever.
• To prevent damage to circuitry,
J,_F_
t
never short-circuit
positive (+)
and negative (-) speaker wires.
• Be sure to connect only positive (red) wires to positive (+)
terminals
and negative
(black) wires to negative
(-)
ter-
minals.
(For SC-CH717 only)
Connect the surround speaker cord.
Rear panel of
Rear panel of
the amplifier
the speakers
Connect the AC power supply cord after you
have connected all other cables.
9
Hide quick links:
Advertisement
Table of Contents
