Table of Contents
Advertisement
24
Timer Recording
With VCR Plus+
Read steps 1-7 to program a timer
recording using VCR Plus+ numbers.
Before you begin make sure:
- Channels have been prograrnmed.
:; The clock has been set.
There is a tape in the VCR (make
sure the tape's record tab is intact
and the tape is long enough to record
the program(s).
The VCR is in VCR position.
You have selected CABLE TV or
TV at the TUNER SET UP menu.
You must do each step within 60 sec-
onds of completing the previous step.
If you don't, you will have to start
again at step 1.
Press the VCR Plus+ button on the
remote control. The on-screen display
shown below will appear.
R PLUS+
PROG.
LUS CO_E=_:_
.... -I
;
END PUSH MENU
J
Press the Number buttons for the VCR
Plus+ number of the progr_
you wish
to record (thzs number is d_fferent for
every program). Finally, press the
VCR Plus+ button.
4t
I
PtuS COOE : _SS'-
[
_ TOSL_n "PUSHVCR÷
]
k
m
CORRECT
PUSH
CLEAR//
"_T,_O END PUSH MENU
../
To record the pro_m-arn once, press the
Number l button to select ONCE. To
record the same program every day
from Monday through Friday, press the
Number 2 button to select DALLY. To
record the same program every week
on the same day (such as every
Saturday), press the Number 3 button
to select WEEKLY.
Pre-ss the Number 1 button to record in
SP speed, or press the Number 2 but-
ton to record in SLp speed. For
details, see page five. You cannot use
the (Tape) SPEED button at this time•
_ONE
TIME
PROGRAM
1
PROGRAM
1
CHANNEL
09
TIME ON
10:30 PM
T]ME OFF
11:30PM
PJEC SPEE_D SLP
=-" SP=I
SLP--21".
_I'ART
DATE 10/10/95
TUE.
END PUSH MENU
Press the MENU button. PROGRAM
WAS COMPLETED / PLEASE TURN
OFF VCR FOR TIMER RECORDING
should appear on the screen. After
three seconds, the on-screen display
will disappear.
If-needed, press the VCR Plus+ button
and repeat steps 2 to 5. When you are
finished, go to step 7.
Turn off the VCR power. The Timer
light will appear. The VCR must be
turned off for a timer recording
to
take place. If you forget to turn the
VCR off, PLEASE TURN OFF VCR
FOR TIMER RECORDING flashes
on your TV screen two minutes before
a timer recording starts. You can
remove it by pressing the CLEAR but-
ton.
The VCR
must be off for a
timer recording
to take place!
Remote Control
POWER Button
VCR Plus+
Button
CLEAR Button
....
MENU Button----J'-
Number Buttons
®®(!
®@(
®®<
-o _
_
b ~
-=--'_ NOTES
• If CODE ERROR appears at step 2
after you enter the VCR Plus+ number,
the number you entered was incorrect
(for example, too short). If this hap-
pens, wait five seconds, then enter the
correct
number.
• To quit VCR Plus+ programming at
any step, press the MENU button. The
on-screen display will disappear from
the TV screen.
• Cancel a VCR Plus+ timer recording
just like you would cancel a regular
timer recording (see page 20for
details).
• To stop a started timer recording, press
the POWER button on the VCR.
• If the power fails for more than three
seconds, programmed timer recordings
may be lost. lf this case, repeat the
steps on pages seven and ten before re-
programming the timer recordings.
See page 42 for more notes.
Advertisement
Table of Contents
