Table of Contents
Advertisement
23
Setting Up VCR Plus+ (cont'd)
Remote Control
MENU button
Number
buttons
Q ® ®
'®
® ®
Q ® Q
o
. ! oQ oe
e eQ • • Q o o e ee
o e*
o = e e * t e oe
oo ee
o • oee*
• eele=
• To correct a guide channel number:
I. Repeat steps 3 - 4 on this page.
2. At step 5, enter the incorrect guide
channel number for both the guide
channel and _he user channel. This
will make the guide channel and user
channel the same.
3. Repe_t steps 3 - 6 again, this time
entering the correct guide channel
and user channel.
• To correct a user channel number:
1. Repeat steps 3 - 4 on this page.
2. At step 5, enter the correct guide
channel and user channel numbers.
• To cancel a pair of numbers:
1. Follow step 9 to display the guide
channel map.
2. Press the CLEAR button. A pair of
numbers will flash.
3. Press the CHANNEL (Up/Down) but-
tons until the pair of numbers you
wish to cancel is flashing.
4. Press the CLEAR button again. The
pair of numbers that was flashing will
disappear.
5. Press the MENU button to exit.
>
: Now, compare the channel numbers
: you have written into the GUIDE CH.
i and USER CH. columns. You'll notice
that some stations have guide and user
: channel numbers that are the same, and
• other stations have channel numbers
• that do not match. Where the channel
: numbers do not match, you must tell
the VCR the guide and user channel
numbers according to the steps below.
Press the MENU button, then press the
Number 2 button to select VCR SET UP.
m.AY
CoN) [
REPEAT PLAY
|
ON SCREEN
MODE
|
LANGUAGE
|
GUIDE
CHANNEL
SET
1
GUIDE
CHANNEL
MAP
)
_O
END PUSH MENU
/
(!:
__j.::
....
Press the Number 5 button to select
GUIDE CHANNEL SET.
SELECT
GUIDE
CH. NO.
END PUSH MENU
:."--_9
Look at the boxes you filled in on
pages 22. For stations whose _maide
channels and user channels are not the
same, press two Number buttons for
the guide channel and two Number
buttons for the user channel.
Always enter "0" before any single
digit channels.
:: If you select line input for the user
channel, press 0, 0. AUX will appear
on-screen.
l_
USER CH;:_--_I:
/
/
CORRECT
PUSH CLEAR ]
END PUSH MENU
Press the Number 1 button so your
VCR will memorize the guide channel
and user channel numbers you have
selected. Or, press the Number 2 but-
ton to quit and select another pair of
numbers.
I
GUIDE
CHANNELSET
_X_
SELECT
PUSH. NUMBER|
GUIDE
CH. 28
[
USER
CH.
O4
MEMORIZE
|
SELECT
ANOTHER
CH.
l
/
CORRECT
PUSH CLEAR/f
END PUSH MENU
!-
Repeat
steps 5 and 6 for all the stations
on your list which have different guide
channel and user channel numbers.
Press the MENU button to exit.
To confirm the guide channel and user
channel numbers you have selected,
press the MENU button to bring up the
main menu display. Then press the
Number 2 button to select VCR SET
UP. Finally, press the Number 6 button
to select GUIDE CHANNEL MAP. A
list of guide channel and user channel
numbers memorized by the VCR will
appear on-screen. If there are more
than ten pairs of numbers, press the
Number l button to view another
screen of numbers.
Make sure these
numbers correspond to the boxes you
filled in in step 1. Then press the
MENU button to exit.
1
:ALIX
2:
2
l
3:3
4:4
23:
S
6:6
7:7
91:
8
9
: 9
10:10
\
TOe.,_..ELiar_Ct._ ]
\
NEx'r_, _
/
Advertisement
Table of Contents
