Changing A Cycle Or Setting; Adding Items During A Cycle; Option Selections; Cycle Status Indicators - Kenmore ULTRA WASH 665.1349 Series Use & Care Manual

........... O tS@t£ 7' _:,j
During the first minute of
a cycle
1. Select a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. The Start/Resume light will flash when the door is opened.
Make sure the door is closed.
4. Press START/RESUME.
After the first minute of a cycle
1. Press CANCEL/DRAIN. The Cancel/Drain light glows. Your
dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. Make sure the door is closed. The Start/Resume light will
flash.
4. Select a new cycle and/or options.
5. Press START/RESUME.
_%,_,;_,/_,_ ,_
You can add an item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before opening the door. The Start/Resume
light will flash.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches. The Start/Resume light
will flash.
4. Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock (see Lock
On section in "Option Selections"), or the Start/Resume light will
continue to flash.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn off the option.
Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher runs the last full
wash cycle and options.
Hi Temp
Select this option to heat the water to 140°F (60°C) during parts
of the cycle. Heating the water helps improve washing results.
This option adds heat, water and wash time to parts of the cycle.
Hi Temp wash is useful when loads contain tough food soil items.
NOTES:
• Pots Pans automatically uses this option. Hi Temp wash is an
option with the Heavy Wash and Normal Wash cycles.
• Use this option for heavier than normal-soiled loads.
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher.
You can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches and
press START/RESUME, or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL!DRAIN.
• To cancel the delay and start the cycle, press START/
RESUME.
Follow the progress of your dishwasher with the Cycle Status
indicators.
®
Clean
Clean
CLEAN glows when a cycle is finished. The light turns off when
you open the door or press Cancel/Drain.
12