Adjusting The Volume; Speaker And Signal Indicators On The Display; Selecting Different Sources For Picture And Sound - JVC RX-7030VBK Instructions Manual

Speaker and signal indicators on the display
By checking the following indicators, you can e_ily confirm which
speakers you are activating and which signals m'e coming into this
receiver.
Speaker indicators
DDD
[suBwF.]
D D
DDD
Signal indicators
L R
LFE
What speaker indicators light depends on the speaker setting
(for details, see "Setting the Speakers" on page 27).
• The frames of "L" "C," "R," "LS," "RS," and "SB" light up,
when the corresponding speakers are set 1o "LARGE" or
"SMALL" and when the speaker is required for 1he Surround/DSP
mode currently seleeled.
• When "SUB WOOFER" is set to "YES," _ lights up (see
page 27).
• All three frames on the row of "SB" are not used al the same time.
When "SBACK OUT" is set 1o "2SPK," the left and the right ones
are used. When it is set Io "1SPK," the middle one is used (see
page 27).
The signal indicators light up to show the incoming signals.
L: • When digital input is selected: Lights up when the [eft
channel signal comes in.
• When analog input is selected: Always lighls up.
R: • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lighls up.
C: Lights up when the center channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
kS: Lights up when the left surround channel signal comes in.
RS: Lights up when the right sun'ound channel signal comes in.
S:
Lights up when the monaural surround channel signal
comes in.
SB: Lights up when the surround back channel signal comes in.
Note:
When "DVD MULTI" is selected as the source, "t_,""C," "R," "LFE," "LS,"
and "RS" light up.
How to understand the soeaker and sienal indicator
illumination
FncEN
[suBwF.],
SB
Ex. No sound comes out of the
center speaker and surround
back speakers though center
channel and surround back
channel signals are coming
into this receiver.
Selecting different sources for picture and
sound
While watching pictures from a video source, you can listen to
sound of an audio source.
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
Press one of the audio source selection buttons while viewing the
picture from a video component such as the VCR or DVD
player, etc.
For RX.8030VBK cD _v_
C )
D D D D [3 [3 CDR TAP_MD
C)
p_NO
c>
On the unit On the remote
For RX.7030VBK/RX-7032VSL
On the unit
Note:
(_CD) PM/AM
TApF_COR
On the remote
When you see the picture through the COMPONENT VIDEO jacks,
you cannot use this function.
L_J L_J
On the front eaneh
To increase the volume, turn MASTER VOLUME clockwise.
To decrease the volume, turn it counlerc[ockwise.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME -.
CAUTION:
Always set the volume to the minimum before starting any sources. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Notes:
• The volume level can be adjusted within the range of"O" (minimum)
to "70" (maximum).
• ffyou set One Touch Operation to "ON"(see page 30), you do not
have to adjust the volume level each time you change the source. It
is automatically set to the stored level.
18