Table of Contents
Advertisement
Cleaning
Your Range H
Oven Window
select models)
S, e ration Pans
Burner Cap &
Ported Burner Rin
(cast iron)
Aeration Pan
(porcelain) -
may be removed
for cleaning,
Surface
Burner
Ignitors
•
o
°
•
•
•
•
•
_, .
Surface
Burner
Grates
(porcelain
on
cast iron)
• Wash with soap and water
or glass
cleaner. Avoid using excessive amounts of water.
Do not use abrasive
cleaners.
"" ;'Wipe
acid'foods and slgar'spdl:immediately
wilh :i_
iloth to'plevlnl
discolora_ionl
" " "
• Light soil -- clean with hot soapy water and a plastic scrubber.
_
"_
Burner Cap
• Moderate
soil -- remove parts to a countertop.
Then clean: 1) spray with a household cleaner,
2) cover with plastic wrap for 15 minutes
3) wipe with a plastic scrubber.
• Stubborn
soils -- scrub with scouring powder.
(Do not use abrasive cleaners, scouring pads or place in
a self-clean oven.) If cleaning powders block gas ports
on burner ring, clean with a straight pin.
To replace parts after cleaning:
ported
_o
Btlr_lpr
_--
Ring
- Ignitor
-
_'
"_
Burner
Post
_
Burner
1) aeration pan - the turned up flanges go the the outside of the burner basin.
2) ported burner ring - align the slot on the bottom of the ring with the locating post
on the burner base, the burner ring and burner base must be in complete contact.
3) burner cap - place on top of the burner tube.
• Clean around ignitor carefully. Avoid catching the ignitor
with cleaning cloth. If ignitor is damaged, the surface burner will NOT light.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
.
•
•
*
• Wash in the dishwasher or in soap and water with a plastic scrubber.
• Do not operate the burners without a pan on the grate. The porcelain finish on the grate may
chip without a pan to absorb the intense heat.
• Grates will become dull and may discolor over time from the heat. This is normal.
* Brand names are trademarks o f the respectivemanufacturers.
: Maintenance
:
Oven Doors
Oven Light Bulb
If the oven door comes off track, realignment can be achieved by
following this simple procedure:
1. Open the door and hold it all the way open.
2. Lock the hinge latches (see illustration),
and gently lift the door
up and partially out until the door is evenly aligned.
3. Evenly slide the door back into place and check to
sure the hinges rest in the center of each door hinge roller.
4. With the oven door fully open, unlock hinge latches and close.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
.
•
°
•
*
•
•
•
•
•
•
•
•
•
o
•
•
•
•
•
Door Hinge Roller
N
Lock
_'- (Close)
\ Unlock
•
*
•
•
•
°
°
Before replacing bulb(s), disconnect power to oven at the main fuse
or circuit breaker panel. Be sure that the oven cavity including the light bulb(s) is cool.
To replace light bulb:
/-
l. Carefully unscrew the glass light lens.
2. To obtain firm grasp on bulb, wear protective rubber gloves. Turn
bulb to the left. Do not touch a hot oven bulb with a damp cloth as
it will break. Note: If the bulb breaks, be certain power supply is
disconnected
and wear protective gloves when removing.
You may
contact an authorized
Jenn-Air
Service Contractor, if needed.
3. Replace bulb with a 40 watt oven-rated appliance bulb. Bulb with brass base is recommended
4. Replace bulb cover and reconnect power to oven.
Hide quick links:
Advertisement
Table of Contents
