Download Print this page

Lubrication; Service; Storage - Hoover SteamVac F5865-900 Owner's Manual

Hide thumbs Also See for SteamVac F5865-900:

Advertisement

_\
f--
mL_tl
tool, and position it against riser.
I tool slowly
over carpet without
pressing trigger (dry stroke)
It is best to alternate wet and dry strokes
as described
above
End with more dry
strokes to aid in faster drying of carpet
Overlap strokes by 1/2 inch to help pre-
vent streaking.
To avoid saturating carpet, do not use
more than 4 wet strokes over any one
area. Always end with dry strokes.
If additiona! cleaning is necessary, wait
until the carpet is completely
dry before
using the tool again.
Empty recovery tank when the motor
sound becomes
higher pitched and
there is a loss in suction (see "Automatic
shut-off", page 7)
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 11.
Read "Before
you begin cleaning"
Instructions on page 9.
Be sure to check the cleaning code on
your upholstery. Use your HOOVER
'SteamVac'
deep cleaner only on
upholstery
marked "W" or "W/S".
Place handle in upright position
Agitator
brushes
will not rotate while
handle Is In upright
position.
Fill clean solution tank with HOOVER
Carpet/Upholstery
Detergent according
to instructions on pages 7 and 8 Attach
tool to end of hose
Do not point powered hand tool or
stair/upholstery
nozzle at people or
pets.
Dry hands and plug deep cleaner into a
properly grounded outlet.
Turn deep cleaner on.
m
Gently press the tool (A) or (B) onto
the fabric
Press the trigger and
slowly pull the nozzle over the fabric
Overlap strokes by 1/2 Lnch to help pre-
vent streaking
Make additional strokes without pressing
the trigger to remove more moisture
To clean in corners or creases, lift the
nozzle one-half inch from the fabric and
press the solution trigger. Vacuum up
the solution with the nozzle without
pressing the trigger.
_For
heavily soiled areas, it may be
necessary to repeat the cleaning
process. Make crisscrossing
strokes to
the original pattern; overlap each pass.
Make no more than 2 passes with the
solution over any one area to prevent
over-wetting
and damage to fabric.
If additional cleaning is necessary, wa!t
until the upholstery is completely
dry
before using the nozzle again
Empty recovery tank when the motor
sound becomes
higher pitched and
there is a loss in suction (see "Automatic
shut-off", page 7)
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 11.
Storage
Before storing:
• Empty solution tank and rinse
thoroughly with clean water.
• Replace empty solution tank and
turn deep cleaner ON. Squeeze
trigger and push deep cleaner for-
ward and back several times to
expel any solution remaining in the
deep cleaner's system. (Do not use
deep cleaner on wood floors.)
• Empty recovery tank and rinse
thoroughly with clean water.
Allow brushes and underside of deep
cleaner to air dry thoroughly before
storing deep cleaner on a carpeted or
wood surface.
Do not store deep cleaner with a full
solution tank In place.
Lubrication
The motor Is equipped
with bearings
which contain sufficient lubrication
for
the life of the motor. The addition of lubri-
cant could cause damage.
Do not add
lubricant to motor bearings.
Service
To obtain approved
HOOVER service
and genuine HOOVER parts, locate the
nearest Hoover Factory Service Center
or Authorized Hoover Warranty
. Service Dealer (Depot) by:
• checking the Yellow Pages under
Vacuum Cleaners - Household"
OR
• checking the list of Factory Service
Centers provided with this cleaner
OR-
• calling 1-800-944-9200 for an
automated referral of authorized
service outlet locations (US. only)
Do not send your cleaner to The Hoover
Company in North Canton for service,
this will only result in delay
If further assistance Is needed, con-
tact The Hoover Company Consumer
Response Center, North Canton, Ohio
44720 Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
Phone: 1-800-263-6376.
Always identify your cleaner by the
complete model number when request-
ing information or ordering parts. (The
model number appears on the bottom of
the cleaner.)
12

Advertisement

loading