Advertisement
Fig (1.1)
Articulating Upholstery Tool*
*Varies per model
Remove all parts from carton and identify each item shown
Make sure all parts are located before disposing of packing materials
Additional parts may be ordered at Hoover.com or call 1 800 944 9200
Note: Remove the screw located in the vacuum base and set aside until instruction 1.3
1.2 Insert handle section into vacuum base Push down firmly
1.3 Using a Phillips screwdriver fasten (1) screw behind handle into vacuum base
1.4 Place bottom of dirt cup into vacuum body first Pivot cup into vacuum Dirt cup is secure when you hear a click
(varies per model)
1.5 Attach bottom of Turbo Tool (A) and pivot into Air powered Tool Clip until secure
1.6 Place Crevice Tool into Wand and slide into tool storage area on left back side (B) of vacuum and place Upholstery Tool or Articulating Tool on right back side (C) of vacuum as shown
Actual model may vary from images shown.
(Fig 2.1)
*Available on select models only
**Varies per model
2.2 Plug cord into electrical outlet
To turn vacuum ON push ON/OFF switch once
To turn vacuum OFF push switch again
for bare floors and very high pile carpet
2.3 For optimal cleaning performance on bare floors and carpet with pile deeper than 1 brushroll should be turned off
The vacuum is shipped with the brushroll in the ON position. To turn brushroll OFF for Suction Only Mode step on pedal (A).
Pedal (A) is inactive when the cleaner is in the upright position.
Brushroll should be in off position for cleaning of high pile carpet deeper than 1
Not to be used for grooming a pet
2.6 To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward.
2.7 The handle of your cleaner has two positions:
2.8 To adjust height setting TURN knob (A) to desired height setting
For maximum cleaning performance the following carpet height settings are recommended:
If the vacuum is difficult to push turn knob to the next higher setting
2.9 To operate dial TURN dial (A) to desired position until it clicks
HOSE position is for cleaning with hose and/or tools
FLOOR position is for general floor cleaning thru nozzle
Vacuum will only pick up debris by the Hose/ Tools when the valve dial is placed into "HOSE position. Valve dial must be returned to "FLOOR position in order to pick up debris thru the floor Nozzle.
Actual model may vary from images shown.
Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas.
The vacuum is ready for tool use when handle is in upright position.
(Tools may vary per model)
(Fig 3.1)
3.2 When using cleaning tools place cleaner handle in the upright position. The agitator brushroll will not rotate when the cleaner is in the upright position.
To remove hose for tool use press the hose release button and pull hose end out.
To lock back into place push hose into hose tube until you hear a click
3.3 Set air valve for desired use Hose/Floor
Turn valve back counterclockwise to FLOOR position until it clicks (A)
Vacuum will only pick up debris by the Hose/Tools when the valve dial is placed into "HOSE" position. Valve dial must be returned to "FLOOR" position in order to pick up debris thru the floor Nozzle
(Tools may vary per model)
Unplug before connecting Air Powered Hand Tool
3.3 Attach tool or wand to the hose (A).
Attach tool to wand (B) by pushing it firmly onto the wand.
Twist wand or tool slightly to tighten or loosen the connection.
To extend wand twist counter clockwise to the unlocked position extend wand & twist clockwise until tight. Reverse to collapse
Not to be used for grooming a pet
To clean Hose and Turbo Tool wipe with a damp cloth. DO NOT submerge in water.
Other cleaning tools may be washed in warm water with a mild detergent. Rinse and air dry 24 hours before using
Actual model may vary from images shown.
3.4 Lift vacuum by Stair Cleaning Handle and position on stairs. Clean forward to back. Never leave the vacuum standing on stairs when not cleaning.
3.5 Use the Hose and Turbo Tool (Tool varies per model) for stair cleaning. When using tools always ensure handle is in upright position
Use extra care when cleaning on stairs. To avoid personal injury or damage and to prevent the cleaner from falling always place cleaner at bottom of stairs on floor. Do not place cleaner on stairs or furniture as it may result in injury or damage. When using tools always ensure handle is in upright position
3.6 Wrap cord around hooks for convenient storage. Attach the plug end to the cord.
Familiarize yourself with these home maintenance tasks as proper use and care of your vacuum will ensure continued cleaning effectiveness.
If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a service center prior to continuing use.
4.1 The System Check ndicator located at (A) alerts you to possible system performance issues.
PROBLEM | POSSIBLE CAUSE | POSSIBLE SOLUTION |
If System Check indicator is red: |
|
|
Any other servicing should be done by an authorized service representative
NOTICE
A Thermal Protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates the cleaner will stop running.
If this happens proceed as follows:
When cleaner is unplugged and motor has cooled for 30 minutes the thermal protector will deactivate and cleaning may continue.
If the thermal protector continues to activate after following the above steps your cleaner needs servicing.
4.2 To maintain optimal performance empty the dirt cup before the dirt cup reaches the max line (A). Place the vacuum in the upright position before removing the dirt cup.
To reduce the risk of personal injury. Unplug before cleaning or servicing. Do not use vacuum without dirt cup or filters in place.
Very fine materials such as face powder or cornstarch may seal the filter and cause a reduction in performance. When using the vacuum for this type of dust empty the cup and clean the filters often.
4.3 Press dirt cup release button (A) and pivot cup out.
4.4 Hold dirt cup over trash receptacle push dirt cup door release lever (B) to open dirt cup door (C).
Close dirt cup door (C). Press firmly to secure at front (D).
4.5 Place bottom of dirt cup into vacuum body first. Pivot dirt cup into vacuum body and press firmly until it locks into place.
To maintain optimal performance filters should be cleaned at least every two months under normal use.
How to Clean:
Remove dirt cup as described in Fig 4.3
4.6 Pull up on dirt cup latch to open
4.7 Pull on filter by the pocket to remove rinsable filter.
Hold filter under running water for at least two minutes to remove dirt and debris. Squeeze filter twice while underwater. Remove from water and squeeze a final time to remove excess water.
Allow filter to dry completely before replacing. Dry filter on edge so air circulates on both sides of filter. This may take up to 48 hours.
Replace filter with pocket and graphics facing up.
Close lid securely by pushing until it clicks.
Replace dirt cup as described in Fig 4.5
To reduce the risk of personal injury. Unplug before cleaning or servicing. Do not use vacuum without dirt cup or filters in place
What to Buy:
When used and maintained properly your Rinsable Filter should not need replacement within the warranty period if desired additional filter is available at Hoover.com or call 1 800 944 9200 Ask for Hoover Part No. 304087001
How to Clean:
4.8 With fingers in slots pull filter frame (A) straight out. Hold filter over a trash receptacle and tap out dirt and debris.
Slide back into position on vacuum.
To reduce the risk of personal injury. Unplug before cleaning or servicing. Do not use vacuum without dirt cup or filters in place.
DO NOT RINSE OR WASH THE FILTER MADE WITH HEPA MEDIA
What to Buy:
When used and maintained properly your Filter should not need replacement within the warranty period if desired additional filter is available at Hoover.com or call 1 800 944 9200 Ask for Hoover Part No. 305687001 Actual model may vary from images shown.
How to Clean:
(Available on select models only).
Your Carbon Filter is located on the underside of the Filter made with HEPA media
DO NOT RINSE OR WASH the Carbon Filter
What to Buy:
Carbon Filter may need to be replaced more often to maintain optimal odor absorbing effectiveness. Additional filter is available at Hoover.com or call 1 800 944 9200 Ask for Hoover Part 902404001
To reduce the risk of personal injury. Unplug before cleaning or servicing. Do not use vacuum without dirt cup or filters in place.
How to Clean:
Remove dirt cup as described in Fig 4.3
4.9 Twist filter assembly (A) counter clockwise. Remove assembly from dirt cup
4.10 Dirt and debris can be cleaned from the filter assembly with the Dusting/Upholstery Tool
4.11 If further cleaning of the internal filter assembly is required turn dust skirt (B) counterclockwise to remove
4.12 Grab dirt cup shroud (C) pull straight off and clean with dusting/upholstery tool.
After cleaning replace dirt cup shroud (C) onto inside edge of filter assembly and align. Place skirt (B) onto shroud align (4) slots with (4) tabs and turn clockwise to lock.
Place the filter assembly (4.9 A) on the dirt cup aligning (3) tabs on filter with (3) slots on dirt cup (B) and twist it clockwise to secure into position.
Replace dirt cup as described in Fig 4.5.
To reduce the risk of injury from moving parts. Unplug before servicing.
4.13 Turn vacuum over so bottom side is facing up and remove the (6) screws (A).
4.14 Pivot out bottom plate away from hidden latch (B) and remove any debris and/or hair from the brushroll.
4.15 Reposition bottom plate aligning latch (B) and fastening all (6) screws (A). Press firmly at latch (B) area to ensure that it is properly latched.
Actual model may vary from images shown.
To reduce the risk of personal injury. Unplug before cleaning or servicing.
4.16 To remove hose for tool use press the hose release button (A) and pull hose end out.
Clear away debris or obstructions from hose. Do not use sharp objects to clean out hose as they can cause damage. To lock back into place push hose into hose tube until you hear a click.
(Tool varies per model)
To reduce the risk of injury from moving parts.
Unplug vacuum before servicing.
4.17 Clean the Turbo Tool by removing the two screws (A) located on the bottom cover with a Phillips head screwdriver.
4.18 Remove the bottom cover (B).
Clean out any debris or hair from the brushroll and turbine fan.
4.19 Replace the bottom cover insert and tighten the (2) screws.
(available on select models only)
To reduce the risk of electric shock. Unplug before cleaning or servicing.
Press Handle Release Pedal and place handle in low position
4.20 Using a Phillips screwdriver remove (2) screws as shown and lift off lens.
4.21 Pull old bulb straight out of socket Push new bulb straight into socket until locked in place.
Do not use excessive force when installing bulb.
Do not twist or turn bulb when installing bulb
4.22 Reposition lens and secure with screws
Additional bulbs may be ordered at Hoover.com or call 1 800 944 9200 Ask for Hoover Part No. 27313-107.
Actual model may vary from images shown.
To reduce the risk of injury from moving parts.
Unplug before servicing.
The belt is located under the bottom plate of the vacuum and should be checked from time to time to be sure it is in good condition
Replace belt if it is stretched cut or broken.
To check the belt refer to Fig 4.26-4.28
4.23 Turn vacuum over so bottom side is facing up and remove the (6) screws (A)
4.24 Pivot out bottom plate away from hidden latch (B)
4.25 Remove used belt from brushroll (C) then from motor shaft (metal rod) (D) and discard
Use only genuine HOOVER belts with your vacuum.
When purchasing a new belt for models with Brushroll On/Off (Suction Only Mode) ask for Flat Belt HOOVER part No. 562289001 or AH20065
If desired additional belts can be purchased at Hoover.com or 1 800 944 9200
4.26 With lettering on outside of belt slide new belt over motor shaft (metal rod) (E)
4.27 Remove any debris and/or hair from the brush roll. Then slip other end of belt around area of brushroll without bristles (F). With belt in place pull and slide brushroll into nozzle making sure that the brushroll end caps are in the correct orientation
4 28 Reposition bottom plate aligning latch (B) and fastening all (6) screws (A).
Press firmly at latch (B) area to ensure that it is properly latched
Rotate brushroll manually to make sure belt is not twisted
The motor and brushroll are equipped with bearings which contain sufficient lubrication for their lifetime.
The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll.
If a minor problem occurs it usually can be solved quite easily when the cause is found by using the checklist below.
Any other servicing should be done by an authorized service representative.
If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a service center prior to continuing use.
To reduce the risk of personal injury.
Unplug before cleaning or servicing.
PROBLEM | POSSIBLE CAUSE | POSSIBLE SOLUTION |
The device won't run |
|
|
System Check Indicator has turned redor The unit won't pick upor Low suction |
|
|
Dust escaping from the unit |
|
|
Headlight not working |
|
|
Device is difficult to push or won't move forward |
|
|
Turbo Tool brushroll won't turn |
|
|
Smoky/burning smell detected |
|
|
To obtain approved Hoover service and genuine Hoover parts locate the nearest Authorized Hoover Warranty Service Dealer (Depot) by:
Do not send your vacuum to Hoover nc Company in Glenwillow for service. This will only result in delay.
If you need further assistance:
To speak with a customer service representative call 1 800 944 9200; Mon Fri 8am 7pm EST. Always identify your vacuum by the complete model number when requesting information or ordering parts (The model number appears on the bottom of the vacuum )
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
For an automated referral to authorized service outlets in the U.S.A phone: 1 800 944 9200 OR visit Hoover online at www.hoover.com.
For additional assistance or information concerning this Warranty or the availability of warranty service outlets phone the Hoover Consumer Response Center Phone 1 800 944 9200 Mon Fri 8am 7pm EST.
SAVE THESE INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
TO REDUCE THE RISK OF DAMAGE:
Be sure to register your product online at Hoover.com or call 1 800 944 9200 to register by phone. Visit Hoover.com for additional video instructions for assembly and maintenance
If you need assistance:
Visit our website at hoover.com. Follow the authorized dealer locator link to find the Hoover authorized dealer nearest you or call 1 800 944 9200 for an automated referral of Hoover authorized dealer locations (U.S. only) or to speak with a customer service representative; Mon Fri 8am 7pm EST
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the UH72630 that isn't answered in the manual? Leave your question here.