Troy-Bilt OEM-290-263 Operator's Manual
Troy-Bilt OEM-290-263 Operator's Manual

Troy-Bilt OEM-290-263 Operator's Manual

Tiller/cultivator power rake attachment

Advertisement

Quick Links

TILLER/CULTIVATOR
THANK
YOU!
Introduction
Please check the contents of the shipping carton against the
Parts List below. If any parts are missing or damaged, be
sure to contact your TROY-BILT Dealer or the Factory.
To help ensure proper installation and safe operation of this
attachment, read and carefully follow these instructions.
Parts List - see Figure 1
Ref. #
Part #
1
Rake Assembly – left side................. 1
2
Rake Assembly – right side .............. 1
3 1915063
Debris Shield .................................... 1
4 GW-H214187
Mounting Strap................................. 1
5 GW-H214186
"S" Hook........................................... 2
6 1983648
1-
1
1
6
4
3
Figure 1
Tools/Supplies Needed for Installation
• No tools are required.
• Fine-grade sandpaper (to remove rust from tine shaft).
• General purpose oil (to lubricate tine shaft).
Thank you for ordering this attachment for your Tiller/Cultivator. We know that it will per-
form to your complete satisfaction if installed and used properly. Refer to the information
below that applies to the attachment you ordered and check the parts
shipped to you. If you have any questions concerning the use of
your POWER RAKE, be sure to contact us for assistance.
Description
"long Spacer................................ 2
4
5
®
Power Rake Attachment
Model 290-263-081 / OEM-290-263
Qty.
2
Safety
Before installing or using this attachment, carefully review
the "Safety Rules" and "Operation" instructions in your
Tiller/Cultivator Owner/Operator Manual. Doing so will
refresh your memory concerning safe operating practices
that must be followed at all times.
CAUTION
TO AVOID INJURY:
• Read the Owner/Operator Manual.
• Know the location and function of all controls.
• Keep all safety devices and shields in place.
• Never allow children or uninstructed adults to
operate the machine.
• Shut off engine and disconnect spark plug wire
before unclogging tines or making repairs.
• Keep bystanders away from machine.
• Keep away from rotating parts.

Advertisement

Table of Contents
loading

Summary of Contents for Troy-Bilt OEM-290-263

  • Page 1 Please check the contents of the shipping carton against the Parts List below. If any parts are missing or damaged, be sure to contact your TROY-BILT Dealer or the Factory. To help ensure proper installation and safe operation of this attachment, read and carefully follow these instructions.
  • Page 2: To Avoid Injury

    CAUTION TO AVOID INJURY: • Before installing or removing the attachment, shut the engine off, allow it to cool, disconnect the spark plug wire and prevent it from touching the spark plug. • The tines may have sharp edges– wear heavy work gloves when handling the tines.
  • Page 3: Operation Tips

    Operation CAUTION • Move the machine outdoors and start the engine (see the TO AVOID INJURY: “OPERATION” section in your Tiller/Cultivator Owner’s • Do not operate machine when you are barefoot or Manual for specific starting instructions). wearing sandals, sneakers, or similar lightweight footwear.
  • Page 4 CAUTION Stop engine, allow it to cool, then disconnect spark plug wire and move it away from spark plug before performing any repairs or maintenance. How to Replace Individual Spring Tines Use the following steps to replace spring tines that are broken or excessively bent.
  • Page 5 • Slowly and carefully pull the attachment bar and the retain- ing bar from the rake assembly. See Photo 10. NOTE: Before removing the spring tines in the next step, it is recommended that you temporarily leave one or two old spring tines on the bars for reference.
  • Page 6: Repair Parts

    POWER RAKE ATTACHMENT REPAIR PARTS...
  • Page 7: Parts Ordering Information

    POWER RAKE ATTACHMENT REPAIR PARTS IMPORTANT: SEE THE REPAIR PARTS PAGES IN YOUR TILLER/CULTIVATOR OWNER/OPERATOR MANUAL FOR PARTS ORDERING INFORMATION. PART PART DESCRIPTION QTY. DESCRIPTION QTY. GW-H213909 Bolt, Socket Hd., 3/8-16 x 1-1/2.. GW-H213908 End Cap – inner......GW-H213911 Wheel/Tire Assembly....GW-H214186 “S”...
  • Page 8 For customer assistance, visit www.troybilt.com, contact your nearest authorized dealer or: TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OHIO 44136-0019, 1-866-840-6483 Printed in U.S.A. Form 769-00070 (01/02)

This manual is also suitable for:

290-263-081

Table of Contents