Panel Display In Edit Mode; Editing A Patch - Zoom 2020 Operation Manual

(3)
BAL 2 – 5 PERK 6 STR
[0-10] [0-10] [0,1]
(1)

Panel Display in Edit Mode

In the Edit mode, the following information is shown on the
panel display.
(1) Effect module on/off
The LEDs of pedals for effect modules which are on
(pedals 1 - 4 and BANK pedal) are lit.
The pedals 1 - 4 and the BANK pedal correspond to
HINT
the following effect modules.
Pedal 1
Pedal 2
Pedal 3
Pedal 3
BANK pedal
(2) Parameter value
The value of the parameter currently selected for editing
is shown on the display.
(3) Parameter type
The type of the parameter currently selected for editing
is indicated by the flashing module cursor LED and
parameter cursor LED.
COMP+ DIST EQ
EFFECT 1 CLN I 3 OD I 5 DST I
1 EQ 2
WAH
2 CLN II 4 OD II 6 DST II
PARM1 COMP HIGH SENS
[–7-+7]
[0-3] [0-10]
PARM2 EDGE MID FREQ
[0,1] [–7-+7] [1-64]
PARM3 3 – 6 GAIN MIDf
[1-8] [1-16]
PARM4 ZNR LOW
[0-15] [–7-+7]
PARM5 LEVEL
[1-8]
1 2
COMP+DIST
EQ
ZOOM
ADVANCED GUITAR EFFECTS PROCESSOR
1
COMP+DIST
EQ
MODULATION
DELAY
REVERB
COMP+ DIST
EFFECT 1 CLN I 3 OD I 5 DST I
1 EQ
2 CLN II 4 OD II 6 DST II
HIGH
PARM1 COMP
[–7- +7]
[0-3]
PARM2
EDGE MID
[0,1] [–7-+7]
3 – 6 GAIN MIDf
PARM3
[1-8] [1-16]
LOW
PARM4 ZNR
[0-15] [–7-+7]
PARM5
1 2
COMP+DIST
MODULATION DELAY REVERB
2 PHA 3 FLG 4 TRM 1 MONO 1 REV
1
PIT
5 STEP 6 CHO 2 PPD 2 E/R
PIT DEPTH TIME
[0-10](x100mS)
[–12-+12] [0-10] [1-10]
DELAY TIME
FINE RATE TONE
[0-99](mS)
[–10-+10] [1-50] [–7-+7]
BAL 2 – 5 PERK 6 STR FEEDBACK MIX
[0-10] [0-10] [0,1] [0-10] [0-10]
MIX
PATCH LEVEL
[0-10]
3 4 B
MODULATION DELAY REVERB
EDIT (MANUAL)
CANCEL PARAMETER SELECT
2

Editing a Patch

• In the Edit mode, use the PARAMETER SELECT
keys to select the desired parameter.
The left/right PARAMETER SELECT keys control the
module cursor LEDs and the up/down PARAMETER
SELECT keys control the parameter cursor LEDs. The
display indication changes accordingly.
HINT
• Use the VALUE +/- keys to change the parameter
value.
The value of the currently selected parameter is changed. To
change values continuously, hold down the key. To change
values quickly, press the other key as well.
EQ MODULATION
2 PHA 3 4
FLG TRM
2 1
WAH PIT
5 6
STEP CHO
PIT DEPTH
SENS
[–12-+12] [0-10]
[0-10]
FREQ FINE RATE
[1-64] [–10-+10] [1-50]
BAL 2 – 5 PERK 6 STR
[0-10] [0-10] [0,1]
LEVEL
[1-8]
3
EQ MODULATION
(EDIT VALUE)
3
DELAY
TIME
[0-90](x100mS)
FEEDBACK
GROUP • BANK
[0-10]
USER
PRESET
( )
BOTH
GROUP
[0-31]
STORE
VALUE
+
–
3 4
The topmost row of parameter LEDs corresponds to
the EFFECT parameter which changes the effect
type. When the effect type is changed, the setting of
parameters 1 - 5 also changes. Therefore it is best to
first select the effect type and then work on the other
parameters when creating an effect from scratch.
DELAY REVERB
1 1
MONO REV
3 DELAY
2 2
PPD E/R
TIME TIME
[0-10](x100mS)
[1-10] [0-90](x100mS)
DELAY TIME
TONE FEEDBACK
[0-99](mS)
[–7-+7] [0-10]
FEEDBACK MIX
[0-10] [0-10]
MIX
PATCH LEVEL
[0-10]
[0-31]
4 B
DELAY REVERB
(2)
11