Table of Contents
Advertisement
Large Frame Snowthrowers
L1226E Models
Mfg. No.
Description
1695326
SMIL1226E, 11.5GT Snowthrower
1695324
SNL1226E, 11.5GT Snowthrower
1695327
SMIL1226EX, 11.5GT Snowthrower (CE)
1695325
SNL1226EX, 11.5GT Snowthrower (CE)
L1428E Models
Mfg. No.
Description
1695330
SMIL1428E, 13.5GT Snowthrower
1695328
SNL1428E, 13.5GT Snowthrower
1695331
SMIL1428EX, 13.5GT Snowthrower(CE)
1695329
SNL1428EX, 13.5GT Snowthrower (CE)
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
07/2007
Initial setup
This Dealer Setup Instruction covers the following products:
M A N U FAC T U R I N G , I N C.
L1530E Models
Mfg. No.
Description
1695334
SMIL1530E, 14.5GT Snowthrower
1695332
SNL1530E, 14.5GT Snowthrower
1695335
SMIL1530EX, 14.5GT Snowthrower (CE)
1695333
SNL1530EX, 14.5GT Snowthrower (CE)
L1632E Models
Mfg. No.
Description
1695338
SMIL1632E, 15.5GT Snowthrower
1695336
SNL1632E, 15.5GT Snowthrower
1695337
SNL1632EX, 15.5GT Snowthrower (CE)
Form No. 1735189
TP 300-4458-00-LW-SN
Advertisement
Table of Contents
Related Manuals for Simplicity L1226E Series
Summary of Contents for Simplicity L1226E Series
- Page 1 M A N U FAC T U R I N G , I N C. Large Frame Snowthrowers Initial setup This Dealer Setup Instruction covers the following products: L1226E Models L1530E Models Mfg. No. Description Mfg. No. Description 1695326 SMIL1226E, 11.5GT Snowthrower 1695334 SMIL1530E, 14.5GT Snowthrower 1695324...
-
Page 2: Safety Rules
Large Frame Snowthrowers SAFETY RULES Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. -
Page 3: Table Of Contents
Large Frame Snowthrowers Table of Contents Unpacking ..........4 1. - Page 4 Large Frame Snowthrowers (2) x Size 15 x 5.0-6 1,38 16 x 4.8-8 TP 300-4458-00-LW-SN 07/2007...
- Page 5 Large Frame Snowthrowers 5/16-18 x 3/4 5/16-18 x 2-1/4 5/16-18 07/2007 TP 300-4458-00-LW-SN...
- Page 6 Large Frame Snowthrowers 3/8-16 >= 3/8” (9.5mm) TP 300-4458-00-LW-SN 07/2007...
- Page 7 Large Frame Snowthrowers 5/16 5/16 07/2007 TP 300-4458-00-LW-SN...
- Page 8 Large Frame Snowthrowers TP 300-4458-00-LW-SN 07/2007...
- Page 9 Large Frame Snowthrowers 07/2007 TP 300-4458-00-LW-SN...
- Page 10 Large Frame Snowthrowers TP 300-4458-00-LW-SN 07/2007...
- Page 11 Large Frame Snowthrowers 07/2007 TP 300-4458-00-LW-SN...
-
Page 12: Perform Safety Checks
Large Frame Snowthrowers Perform Safety Checks Check Engine Controls 1. Make sure all safety guards are in place and all nuts, bolts, clips, cotter pins and wires are secure. 2. Check to make sure spark plug wire is attached. 3. Check all controls for proper operation: a. -
Page 13: Check Snowthrower Controls
Large Frame Snowthrowers Perform Safety Checks Check Snowthrower Controls 1. Check the skid shoes to make sure they are set at the desired height. Adjust if necessary. 2. Check the traction drive control (B, Figure 2). Snowthrower motion should stop when the control is released. -
Page 14: Auger Drive Adjustment
Large Frame Snowthrowers Auger Drive Adjustment WARNING Do not over-tighten, as this may lift the lever and cause auger drive to be engaged without depressing the Auger Control. 1. Check that the auger cable (A, Figure 3) is on top of cable button (B) as shown in Figure 3. -
Page 15: Speed Drive Adjustment
Large Frame Snowthrowers Figure 6. Bottom Cover A. Capscrews B. Bottom Panel Figure 5. Traction Drive Cable Adjustment C. Auger Housing A. Cable Boot B. Traction Drive Cable C. “Z” Hook D. Cable Adjustment Bracket Note: If the cable is too slack the unit will not drive. If the cable is too tight the drive will be engaged without pushing the handle down. -
Page 16: Easy Turn™ Cable Adjustment
Large Frame Snowthrowers EASY TURN™ CABLE ADJUSTMENT If the Easy Turn™ cable has stretched, the gears will not disengage when the control lever is activated. Adjust the cable using the following procedure. 1. Turn the engine off and disconnect the spark plug wire. -
Page 17: Scraper Bar & Skid Shoe Adjustment
Large Frame Snowthrowers Scraper Bar & Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be high enough so that it will not pick up gravel or debris. The height of the scraper bar is controlled by raising or lowering the Skid Shoes (See Figure 10). -
Page 18: Belt Adjustment
Large Frame Snowthrowers Belt Adjustment Auger Drive Belt If your snowthrower will not discharge snow, check the control cable adjustment. If it is correct, then check the condition of the auger drive belt. If it is damaged or loose,replace it (see Belt Replacement in this section of the manual). - Page 19 Large Frame Snowthrowers Belt Replacement Auger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person. If the auger drive belt is damaged, the snow thrower will not discharge snow.
- Page 20 Large Frame Snowthrowers Figure 16. Frame and Axle Housing A. Upper Capscrews B. Lower Capscrews C. Auger Housing Figure 15. Spout Rotator Rod D. Frame A. Special Nut B. Cover 16. Slide spout rotator rod (B, Figure 17) into hex dash C.
- Page 21 Large Frame Snowthrowers 22. Adjust the belt guide. See “Belt Adjustment” in the 13. Adjust the belt guide. See “Belt Adjustment” in the Adjustment section. adjustment section of the manual. 23. Install the belt cover (A, Figure 11). Tighten screws 14.
- Page 22 Large Frame Snowthrowers M A N U F A C T U R I N G , I N C . 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com P R O D U C T S 535 Macon Street McDonough, GA 30253 www.Snapper.com...