Full One Year Warranty - Craftsman 113.226423 Owner's Manual

i= ....... i , , , i
FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER
If within one year from the date of purchase, this Craftsman Belt and Disc Sander fails due
to a defect in material or workmanship,: sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY RETURNING TH E BELT AND DISC SANDER TO
THE NEAREST SEARS RETAIL/CATALOG STORE OR SERVICE CENTER/DEPARTMENT IN
THE UNITED STATES:
THIS WARRANTY APPLIES ONLY WHIL E THIS PRODUCT IS IN USE IN THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCK AND CO., Sears Tower, BSC 41-3, Chicago, IL 60684
general safety instructions for power tools
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
Iabels affixed to the tool. Learn its application and
limitations as welI as the specific potential hazards
peculiar to this tool.
2. GROUND ALL TOOLS
This tool is equipped with an approved 3-conductor
cord and a 3-prong grounding type plug to fit the
proper grounding type receptacle. The_green con-
ductor in the cord is the grounding wire. Never
connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE
In working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTING KEYS AND
WRENCHES
Form a habit of checking to see that keys and
adjusting wrenches are removed from toot before
turning it on.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.
Floor must not be slippery due to wax or sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or
expose them to ra_noKeep work area welt lighted.
Provide adequate surrounding work space.
7. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from
work area.
8. MAKE WORKSHOP CHILD-PROOF
--with padlocks, master switches, or by removing
starter keys.
9. DON'T FORCE TOOL
it wilt do the job better and safer at the rate for
which it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment to do a job it was
not designed for.
11. WEAR PROPER APPAREL
Do not wear loose ctothing, gloves, neckties or
jewelry (rings, wrist watches) to get caught in mov-
ing p_.rts. Nonslip footwear isrecommended. Wear
12,
USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles _must comply with ANSI
Z87.1 ) at all times Everyday eyeglasses only have
impact resistant lenses_ they are NOT safety gJas-
ses. Also, use face or dust mask if cutting operation
is dusty, and ear protectors (plugs or muffs) during
extended periods of operation,
13.
SECURE WORK
Use clamps or a vise to hold work when practical
It's safer than using your hand. frees both hands
to operate tool.
14. DON'T OVERREACH
Keep proper footing and batance al all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changing accessories.
16. DISCONNECT TOOLS
Before servicing; when changing accessories such
as blades, bits, cutters, etc.
17, AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plug-
ging in.
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended ac-
cessories. Follow the Enstructions that accompany
the accessories. The use of improper accessories
may cause hazards.
19, NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if
the cutting tool is accidentally contacted.
Do not store materials above or near the toot such
that it is necessary to stand on the tool to reach
them.
20. CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
ensure that it wilt operate properly and perform its
intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
protective hair covering to C0ntain iong ha
long sleeves above the elbow.:; : ......, ,...... should be properly repaired or replaced,