Store Battery; Date/Time Settings; Charging The Battery Pack - JVC GR-SXM250 Instructions Manual

STORE BATTERY:
Be sure to fully discharge a battery pack by
performing the following steps before storing it for
a long period of time, otherwise the battery
performance will be reduced.
1) Attach the battery to the camcorder with no
cassette inserted.
2) Set the Power Switch I_ to "[]" or "[_" while
pressing down the Lock Button _) located on the
switch.
• During charging or discharging, the camcorder
cannot be operated.
• Charging and discharging is not possible if the
wrong type of battery is used.
• When charging the battery pack for the first time
or after a long storage period, the CHARGE lamp
_) may not light. Remove the battery pack from
the camcorder, then try charging again.
• If a fully-charged battery's operation time remains
extremely short, the battery is worn out. Please
purchase a new one.
• Perform charging where the temperature is
between 10°C and 35°C (50°F and 95°F). 20°C to
25°C (68°F to 77°F) is the ideal temperature range
for charging. If the environment is too cold,
charging may be incomplete.
• Charging time varies according to the ambient
temperature and the status of the battery pack.
• Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure to
use it only in well-ventilated areas.
• The following operation stops charging or
discharging:
• Set the Power Switch I_ to "PLAY", "[]" or "_ ".
• Disconnect the AC Adapter from the camcorder.
• Unplug the AC Adapter's power cord from the
AC outlet.
• Detach the battery from the camcorder.
• Using the optional AA-V15 AC Power Adapter/
Charger, you can charge the BN-Vll U/V12U/
V20UN400U battery pack without the camcorder.
However, it cannot be used as an AC adapter.
• To avoid interference with reception, do not use
the AC Adapter near a radio.
• Recording time is reduced significantly when
Zoom or Record-Standby mode is engaged
repeatedly or the LCD monitor is used repeatedly.
• Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
Date/Time Settings
1) Set the Power Switch I_ to "_" while pressing
down the Lock Button _) located on the switch.
2) Press the MENU Wheel O in. The Menu Screen
appears.
3) Rotate the MENU Wheel O to select
"I_TO SYSTEM MENU" and press it to display
SYSTEM MENU. Rotate the MENU Wheel O to
select "1_ NEXT" and press it to display the next
page.
4) Rotate the MENU Wheel O to select "DATE/
TIME" and press it. The DATE/TIME Menu
appears.
5) To set "YEAR", "MONTH", "DAY" or "TIME"
(hour/minute), rotate the MENU Wheel O to
select the desired item, and press it. When the
setting begins blinking, rotate the MENU Wheel
O until the correct setting appears and then
press it. The setting stops blinking.
6) When none of these settings ("YEAR",
"MONTH", "DAY", "TIME") blinks, rotate the
MENU Wheel O to select "1_EXIT", and press it.
The Menu Screen reappears with the highlight
bar on "1_ RETURN".
7) Press the MENU Wheel O in to close the Menu
Screen.
• To display the date and time in the camcorder's
display and on a connected TV, see DATE/TIME
DISP. (_._. pg. 21) in SYSTEM MENU.
• The date/time cannot be stored in memory if the
built-in clock battery runs out. Consult an author-
ised JVC dealer for replacement, or set the date/
time as necessary before you start shooting.
O
e
DAY 28
TIME PM8:20
_EXIT
12-hour
indication with
AM to PM
I