MTD OEM-190-032 Operator's Manual
MTD OEM-190-032 Operator's Manual

MTD OEM-190-032 Operator's Manual

42-inch two-stage snow thrower attachment
Hide thumbs Also See for OEM-190-032:

Advertisement

Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR'S MANUAL
Model
OEM-190-032
190-032-101
42-inch Two-Stage Snow Thrower Attachment
For FastAttach
Compatible Lawn Tractors & Garden Tractors
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
FORM NO. 769-01933
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
6/2005
PRINTED IN U.S.A.

Advertisement

Table of Contents
loading

Summary of Contents for MTD OEM-190-032

  • Page 1 (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. FORM NO. 769-01933 MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 6/2005 PRINTED IN U.S.A.
  • Page 2: Table Of Contents

    This Operator’s Manual is an important part of your snow thrower attachment. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. TABLE OF CONTENTS 1. Rider Model Identification ........ Page 3 9.
  • Page 3: Rider Model Identification

    FastAttach Snow ™ Model Plate Thrower Attachment NOTE: This Operator’s Manual covers several models. Snow thrower hook-up instructions vary by model. Not Rider Model all features discussed in this manual are applicable to all snow thrower attachments. Identification To The Owner Model OEM-190-032 42-inch two-stage snow thrower attachement is designed for use on FastAttach™...
  • Page 4 WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm. DANGER: This machine was built to be operated according to the rules for safe operation in this manual.
  • Page 5 Operation Maintenance & Storage 1. Do not put hands or feet near rotating parts, in the 1. Never tamper with safety devices. Check their proper auger/impeller housing or chute assembly. Contact with the operation regularly. Refer to the maintenance and adjust- rotating parts can amputate hands and feet.
  • Page 6: Carton Contents

    Cotter Pin retailer where you Assembly Brackets purchased this unit, & Hardware call MTD directly at Chute Directional 1-330-220-4MTD or Support w/ Tilt Lever toll free at & Upper Crank Rod 1-800-800-7310. Upper V-Belt...
  • Page 7 • Left & Right Assembly Brackets (683-04215 & 683-04214) & Hardware (710-0514 Hex Screw, 712-04065 Flange Nut, 738-0143 Shoulder Screw & 712-04063 Flange Nut) purchased this unit, • Belt Keeper (711-1000) & Flange Lock Nut (712-04063 ) call MTD directly at • Wing Nut (712-04100) 1-330-220-4MTD • 16mm Clamp (726-0354) or toll free at •...
  • Page 8 WARNING: Before installing attach- Weld Pin ment, place tractor on a firm and level surface. Place the PTO in the disen- gaged (OFF) position, set the parking brake, shut engine off and remove key to prevent unintended starting. Assembly NOTE: References to LEFT and RIGHT indicate the left and right sides of the tractor when facing forward in the Model Series operator’s position.
  • Page 9 Reversing the Flange Nut, Washer & Shoulder Spacer Idler Assembly Hardware (Manual PTO Garden Tractors equipped with a 46-inch deck ONLY) Assembly If you’re mounting this snow thrower attachment to a Model Series tractor equipped with any deck other than a manually engaged 46-inch, proceed to either: 600-649 &...
  • Page 10 Mounting the Idler Assembly Extension Spring (42, 46, 50, 54 inch Decks with Electric PTO) Flange Nut If you’re mounting this snow thrower attachment to a tractor equipped with any deck other than a 42, 46, 50 Assembly or 54-inch deck with electric PTO, proceed to Mounting the Undercarriage Assembly (all tractors).
  • Page 11 Mounting the Idler Assembly PTO Cable (38 and 42-inch Decks with Manual PTO) Flange Nut If you’re mounting this snow thrower attachment to a tractor equipped with any deck other than a 38 or Assembly 42-inch deck with a manual PTO, proceed to Mounting the Undercarriage Assembly (all tractors).
  • Page 12 Because this snow thrower attachment is compatible with several model lawn tractors and garden tractors with either an electric PTO or a manual PTO, four upper drive belts are included. If you have had any problems locating the proper upper belts for installation in the V-Belt previous steps, use the table below for quick reference.
  • Page 13 3. Align the holes in the rear of the lift arms with the holes in the rear of the undercarriage and insert the Lift Arm clevis pins removed in step 1. Fasten with the hairpin clips. See Figure 14. 5. Move the tractor’s deck lift lever into the top notch on the right fender allowing the lift arms and the rear of Assembly the undercarriage assembly to rise.
  • Page 14 Bracket Assembly Flange Lock Nuts WARNING: Before installing attach- ment, place tractor on a firm and level surface. Place the PTO in the disen- Hex Screws gaged (OFF) position, set the parking Bracket & brake, shut engine off and remove key to prevent unintended starting.
  • Page 15 Mounting the Undercarriage Spindle Pulley Belt Keeper Assembly Make certain the correct upper drive belt (754-0498) is installed on the undercarriage assembly. If the appropri- ate belt is not installed, replace it with the correct belt Bracket & prior to proceeding with mounting the undercarriage. Undercarriage IMPORTANT: Make certain that the flat side of the belt is facing outward as it sits against both the idler pulley...
  • Page 16: Controls

    Upper Chute Crank Rod Joint Block Lower Chute Assembling Crank Rod Controls All Models Chute Directional Control Assembly NOTE: All references to left Figure 24 or right side of the Attaching the Chute Attaching The snow thrower is from the operating Directional Control Lift Handle position only.
  • Page 17: Housing Assembly

    Mounting Inset A Auger Housing All Models WARNING Before installing attachment, place tractor on a firm and Inset B level surface. Place Figure 27 the PTO in the disen- Mounting the Auger support bracket. Have your assistant pull the support gaged (OFF) position, pin on the right side of the auger housing outward Housing Assembly...
  • Page 18 Routing the Upper Drive Belt (Tractors Models with an Electric PTO) Spindle Pulley Engine Pulley All electric PTO Decks 42, 46, 50, 54 Idler Pulley Belt Routing Various Models PTO Idler Pulley Figure 29 1. Attach and route the upper drive belt around the spindle pulley and idler pulley found on the undercarriage, the electric PTO clutch and the PTO idler pulley as illustrated in Figure 29.
  • Page 19 Routing the Upper Drive Belt (Older Style Tractors ) 46 in. manual older style setup Belt Routing Various Models 42 in. electric and manual older style setup WARNING Before installing attachment, place tractor on a firm and level surface. Place the PTO in the disen- Figure 31 gaged (OFF) position,...
  • Page 20 Chute Directional WARNING: Be familiar with all controls and their proper operation. Control Know how to stop the machine and disengage them quickly. The chute directional control assembly is found on the left side of the tractor and includes both the chute tilt lever as Engaging the Augers well as the chute crank.
  • Page 21: Operation

    OPERATION a foreign object, move the PTO into the disengaged (OFF) position immediately and turn off the tractor’s WARNING: Read, understand, and engine and remove the ignition key. Examine the auger follow all instructions and warnings area thoroughly for damage and do NOT operate the on the tractor, attachment, and in the snow thrower attachment until any damage is repaired.
  • Page 22: Adjustments

    Making Adjustments Lift Cable Hex Nuts WARNING: Never attempt to make any adjustments while the engine is running, except where specified in the Operator’s Manual. Place tractor on a firm and level surface. Place the PTO in the disen- Adjustments gaged (OFF) position, set the parking brake, shut engine off, and remove key All Models...
  • Page 23: Maintenance

    Maintenance Lube Spiral and Chute Base WARNING: Before lubricating, repairing, or inspecting, place tractor on a firm and level surface. Place the PTO in the disengaged (OFF) position, set the parking brake, shut engine off, Maintenance and remove key to prevent unintended starting.
  • Page 24 �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� � � � �� � �� �� � �� � �� �� �� ��...
  • Page 25: Parts List

    Part List: PART DESCRIPTION PART DESCRIPTION Qty. NUMBER NUMBER Snow 618-04315 Auger Gear Box 721-0327 Grease Seal (Incl. Ref. 23-41) Thrower 684-0158 Impeller Assembly, 12” 736-0351 Flat Washer, .76 x 1.5 x .030 684-0148 Housing Assembly 736-0369 Flat Washer, .508 x 1.0 x .020 Attachment 703-2734 Housing Brace Bracket...
  • Page 26 �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � � �� �� � �� �� � � �� � � �� �� �� �� � �� � �� �� � �� � �...
  • Page 27 PART No. DESCRIPTION Qty. PART No. DESCRIPTION Qty. 720-0232 Knob 736-0366 Flat Washer, .64 x 1.12 x .125 Part List: 784-5604 Chute Tilt Handle 736-0452 Bell Washer, .396 x 1.14 x .095 Snow 731-1313C Chute Tilt Cable Guide 736-3069 Flat Washer, .531 x .875 x .15 Thrower 712-04063 Nylon Hex Lock Nut, 5/16-18...
  • Page 28 �� �� �� � �� �� �� �� �� � �� �� � �� �� �� �� �� � �� �� � �� � �� �� �� � �� �� �� � �� �� �� �� �� �� �� �� ��...
  • Page 29 Part List: Snow PART No. DESCRIPTION Qty. PART No. DESCRIPTION Qty. Thrower 618-0411 Spindle Assembly 712-0241 Hex Nut, 3/8-24 (Incl. 38-44) 683-04210 Pulley Mounting Bracket 732-0978 Extension Spring, .620 x 5.62 Attachment 710-0347 Hex Cap Screw, 3/8-16 x 1.75 736-0169 Lock Washer, 3/8 710-1260A Self Tapping Screw...
  • Page 30: Notes

    NOTES: Use this page to make notes and write down important information.
  • Page 31 NOTES: Use this page to make notes and write down important information.
  • Page 32: Warranty

    MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect to e. MTD does not extend any warranty for products sold or exported new merchandise purchased and used in the United States, its posses- outside of the United States, its possessions and territories, except sions and territories.

This manual is also suitable for:

190-032-101190-032-10

Table of Contents