Advertisement
Quick Links
lSearsi
o wners
manual
MODEL
NO.
113.197702
SAW ONLY
113.197752
SAW WITH LEGS
Serial
Number
Model and serial
number may be found
at the front of the base.
You
should
record
both
model
and serial
number
in a safe place for
future
use.
CAUTION:
Read
GENERAL
and
ADDITIONAL
SAFETY
INSTRUCTIONS
carefully
CRRFTSMRNo
IO-INCH
RADIAL
SAW
• assembly
• operating
• repair
parts
Sold
by SEARS,
ROEBUCK
AND
CO.,
Chicago,
IL. 60684
U.S.A.
Part No. 63871
Prir_ted in U SA
Advertisement
Related Manuals for Craftsman 113.197752
Summary of Contents for Craftsman 113.197752
- Page 1 lSearsi o wners manual MODEL 113.197702 SAW ONLY 113.197752 SAW WITH LEGS Serial Number Model and serial number may be found at the front of the base. CRRFTSMRNo should record both model and serial number in a safe place for future use.
- Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN RADIAL If within one year from the date of purchase, this Craftsman Radial Saw fails due to a defect in material workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY...
- Page 3 additional safety instructions for radial saws between column & column support, or in the CAUTION: Always disconnect power cord before carriage, and that arrn, yoke, and bevel locks/clamps removing the guard, changing the cutting tool, changing the are tight. set-up making adjustments.
- Page 4 additional safety instructions for radial saws removed from arbor before using Therefore, rip with the finished side down (next accessory shaft (rear end of the saw motor). NEVER table) and be especially attentive to following operate the saw with cutting tools (including sanding...
- Page 5 (C)CROSSCUTTING dadoing o r molding, when thesawblade guard m ust beused. S ee detailed instructions thataccompany 1. ALWAYS RETURN THECARRIAGE TO THE the dadohead, m olding head, a ndmolding head FULLREARWARD POSITION ATCONCLUSION guard. OFEACH CROSSCUT TYPE OPERATION. Never 3. The useof grinding wheels, abrasive o r cut-off remove yourhand fromtheYokeHandle unless the wheels, or wirewheels, canbedangerous andisnot...
- Page 6 electrical connections adapter as shown below is available for connecting plugs to 2-prong receptacles. green grounding extending from adapter must be connected to a permanent ground such as to a properly grounded outlet box. GROUNDING ADAPTER 3-PRONG PLUG 2-PRONG Connections for 240V A.C.
- Page 7 2. After coolingto a safeoperating t emperature, the voltage (such as small size wires in the supply circuit) overload p rotector canbeclosed m anually by pushing overly-long supply circuit, Always check in theredbuttonon thetopof themotor. I f thered connections, the load and the supply circuit, whenever buttonwill notsnap intoplace i mmediately, themotor...
- Page 8 CONTENTS Location and Functions of Controls ....Guarantee ........Basic Saw Operations ......General Safety Instructions for Power Tools ..Additional Safety Instructions for Radial Saws ..Adjustments to Compensate for Wear ....Trouble-Shooting ......Electrical Connections ......Maintenance and Lubrication ....
- Page 9 following parts included with Model 113.197752. Table of Loose Parts QtY. Leg ........Stiffener, L.H ......Stiffener, R.H ......Loose Parts Bag Part No. 63752 (containing the following items): © - Screw, Truss Hd. 1/4-20 x 5/8 ....- Lockwasher, 1/4 External ....
- Page 10 X in top of legs. Install screws, washers and nuts as shown. If you mount the saw on any other Craftsman base or flat bench, make sure Elevation Crank has proper clearance rotate.
- Page 11 assembly and alignment positive switch is "OFF" and power cord unplugged thru-out entire procedure. .f'_ _,,,..__ WARNING REMOVE CARRIAGE STOP SCREW, LOCKWASHER LOCKWASHER TAG. Read understand warning before discarding. i_._.._ S!OP SCREW "L" WRENCH SUPPLIED LOCK BEFORE PROCEEDING. HOLDING CARRIAGE ASSEMBLY WITH BOTH...
- Page 12 ALIGNMENT PROCEDURE IMPORTANT: SQUARE SCREW 5/16-18x 3/4 IN ORDER TO OBTAIN MAXIMUM CUTTING [ABLE MOLJNTI TABLE MOUNTING ACCURACY, FOLLOWING STEPS SUPPORT CHANNEL SUPPORT CHANNEL MUST CAREFULLY FOLLOWED. BECOME THOROUGHLY FAMILIAR WITH THESE STEPS SO THAT YOU CAN ALWAYS MAINTAIN YOUR PROPER HERE ALIGNMENT.
- Page 13 assembly and alignment FRONT TABLE UPSIDE DOWN POSITION) BOTTOM SIDE HOLE TABLE TABLE HOLD DOWN SCREWS T-NUT T-NUT (TYPICAL) INSTALLATION OF FRONT (WORK) TABLE. Place front table board upside down on a workbench floor. Drive T-nut into hole that is not counterbored.
- Page 14 Loosen (2) 1/4 _ 20 Gib set screws on the left side at the rear of the column support. HEX "L" WRENC i,_._J Elevate, then lower the Arm: (a) if the column binds and elevation is difficult loosen 5/16 plated bolts on front side of the column...
- Page 15 assembly and alignment Lower until saw blade just clears the front table. Lock the yoke clamp handle and bevel lock lever. Place a framing square table as shown position the blade and square until the leg of the square just contacts a tooth of the blade.
- Page 16 STEP FOUR SQUARING SAW BLADE TO (WORK) TABLE NOTE: If alignment procedure step one was not performed, this adjustment can not be accomplished. Place a framing square on the table with the short against the saw blade. Do not allow the square to rest RIP FENCE...
- Page 17 assembly and alignment l o correct "'heel" condition proceed as follows: Remove left hand carriage cover• HEAD SCREWS Loosen the yoke clamp handle• Loosen (slightly) the two hex head screws. Rotate yoke assembly until gap between saw blade and square is eliminated, Lock yoke...
- Page 18 STEP SIX SCREW ADJUSTING SCALE INSTALLING INDICATORS. NOTE: The rip scales and pointers are intended be used quick settings. greater accuracy, _lP SCALE take direct measurement between blade and fence. Pre-assemble indicator and twin nut, loosen but do INDICATOR remove the two screws which...
- Page 19 assembly and alignment ALIGNMENT OF SPREADER FOR RIPPING. WARNING: NEVER POSITION GUARD ANTIKICKBACK ASSEMBLY WITH POWER ON; NOR POSITION ANTIKICKBACK PAWLS GRASPING PAWLS OR SPREADER. Install Blade Guard. Sight (visually) check proper alignment spreader with saw blade as shown. If the spreader not aligned, adjust it as follows:...
- Page 20 locations and functions of controls versatility Radial is due, in part, to its controls, and these are the keys to its successful operation. Learn to use the controls all operations before actually starting to saw. A series of six diagrams is located on the top surface of the arm.
- Page 21 Proper Indexing Method Experienced operators bevel lock lever locks motor to the yoke woodworking equipment, such as this Craftsman Radial when motor is in position. Pull lever to Saw, acquire habit indexing in one direction release and push to lock.
- Page 22 WARNING: FOR YOUR OWN SAFETY ALWAYS Spreader LOCK SWITCH "OFF" WHEN IS NOT prevent kerf from closing m on sawblade IN USE. REMOVE KEEP IT IN A SAFE possible kickback; PLACE . . . ALSO IN THE EVENT OF A POWER FAILURE (ALL YOUR...
- Page 23 HA VE YOU FOLLO WED ALL SIX STEPS ALIGNMENT PROCEDURE? IF YOU HAVE FOLLOWED THEM THEIR PROPER SEQUENCE, CANNOT EXPECT A CCURA TE CUTTING RESUL TS. THIS EDGE OF BOARD AGAINST FENCE FOR ALL CUTS FENCE In addition to the proper alignment of your saw, you must...
- Page 24 basic saw operations REQUIREMENTS FOR CROSSCUT Board position (stationary) against fence (guide) laying flat on table top. (OPERATIONS 1 THROUGH Arbor must be tight and saw blade guard installed in horizontal position. Arm control lever must be in locked position. Adjust the antikickback assembly...
- Page 25 basic saw operations OPERATION No. 2 - MITER CROSSCUT Miter crosscutting is the process of sawing a board at any angle other than a 90 ° (square) cut. The 45 ° miter angle is a popular one, since boards 45 ° assembled to form a 90 °...
- Page 26 REQUIREMENTS WHEN RIPPING (OPERATIONS 5 AND Carriage lock knob must be locked. Radial arm must be locked in 0 ° position. Work must be held firmly against table and fence while feeding through. Guard spreader and antikickback (AKB) assembly must properly set.
- Page 27 Since the work is pushed along the fence, it must have a straight edge in order to make sliding contact with fence. Also, the work must make solid contact with table, so that it will not wobble. Provide a straight edge, even if this...
- Page 28 adjustments to compensate for wear ADJUSTING BEVEL LOCK LEVER purpose this lever is to lock motor at any angle. adjust, remove set screw with wrench shown bevel lock lever as a wrench tighten clamp bot. Over Tighten. Replace bevel CC(P q ,,vELLocK lock lever locked...
- Page 29 adjustments to compensate for wear 3/8-16 BOLTS TO COLUMN With control lever unlocked index release position, the arm should move firmly with vertical play in the arm. The arm should fit snugly on the column. If not, then adjust. Remove screws from rear cover...
- Page 30 LOCK ADJUSTING WHEEL control lever operates a brake shoe that locks releases the arm, and automatically releases the arm index pin for 0 ° & 45 ° miter settings. lock action should feel tight and secure. Considerable amount of effort must be applied to the lever...
- Page 31 trouble-shooting F,.,s. cutENDSOUSE C0T E ND .OOARE WARNING: REMOVE POWER CORD FROM POWER SOURCE BEFORE TROUBLE SHOOTING. NOTE: Changing one adjustment will effect another, so it is best. to perform alignment procedures when correcting any one problem. The usual operating "troubles"...
- Page 32 trouble-shooting WOOD BINDS, SMOKES MOTOR SLOWS DOWN OR STOPS WHEN RIPPING. Dull blade or warped board. Sharpen replace blade. Avoid attempted use of severly warped material. Feed rate too fast. Slow Feed Rate. Saw blade heels. Check align described Alignment Procedure Section, Step Five.
- Page 33 MOTOR TROUBLE - SHOOTING CHART NOTE: Motors used on wood-working tools are particularly susceptible to the accumulation of sawdust and wood chips should be blown "vacuumed" frequently prevent interference with normal motor ventilation. TROUBLE PROBABLE CAUSE SUGGESTED REMEDY Motor will not run. 1.
- Page 34 OUTLET BEFORE MAINTAINING LUBRICATING Do not lubricate between radial arm cap and radial arm. YOUR SAW. When receive your Craftsman radial saw, PERIODICALLY LUBRICATE THESE POINTS requires no lubrication. radial saw has been partially aligned and all bearings are lubricated and sealed for life.
- Page 35 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 _"--.- 1 8...
- Page 36 PARTS LIST FOR CRAFTSMAN IO-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 Always order by Part Number - Not by Key Number. FIGURE Part Description Description Key I Part ,,ul 63518 STD 551025 Cord, with Plug *Washer, 17/64 x 5/8 x 1/32...
- Page 37 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 €_ //34 28 29 eAny attempl: to repair this motor may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Store.
- Page 38 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 FIGURE 3 - YOKE ASSEMBLY Part Part Description Description STD 601105 *Screw, Type "T" Pan Hal. 10-32 x I/2 STD 551037 *Washer, .380 x 47/64 x 1/16 63661 Cover, L.
- Page 39 "'R PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113,197752 Figure 4...
- Page 40 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 FIGURE BASE ASSEMBLY Part Part Description Description STD 503705 *Screw, Soc. Set 3/8-16 x !/2 STD 580014 *Key, Woodruff 1/8 x 1/2 63623 Latch, Arm 63619 Support, R. H.
- Page 41 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 ¢6 FIGURE 5 - ARM ASSEMBLY Part Part Description Description 63636 Pin, Clevis 63626 Housing, 63667 Clamp, Cord 63629 Pin, Arm Index STD 601103 *Screw, Type "T"...
- Page 42 PARTS LIST FOR CRAFTSMAN 10-INCH RADIAL MODEL NUMBER 113.197702 AND 113.197752 FIGURE GUARD ASSEMBLY Part Part Description Description 63681 Guard STD 582043 *Ring. Retaining 7/16 120399 63270 *Nut, Square, 5/16-18 Spreader 63541 63269 Bar, Antikickback Bearing 63540 63539 Screw, Guard...
- Page 43 ISearsl owners IO-INCH RADIAL SAW manual SERVICE that have purchased your 10-inch radial saw, should need ever exist repair parts or service, simply contact Sears Service Center most Sears, Roebuck Co. stores. Be sure to provide arl pertinent facts when call or visit.