Craftsman 113.197250 Operator's Manual

1o" electronic radial saw with 23" cabinet and 1 door; 10" electronic radial saw with leg set

Hide thumbs Also See for 113.197250:

Owner's manual (20 pages)

100

101

102

103

104

Table Of Contents

105

Table of Contents

Quick Links

Summary of Contents for Craftsman 113.197250

Page 1 Save This Manual For Future Reference _ARS Operators Manual MODEL NO. 113.197210 1O" ELECTRONIC 113.197210 RADIAL SAW WITH 23" CABINET AND 1 DOOR 113.197250 10" ELECTRONIC RADIAL SAW WITH LEG SET Serial CRRFTSMRN Number Model and serial numbers may be found at the rear of the base.
Page 2: Table Of Contents
FULLONEYEAR WARRANTY ONCRAFTSMAN RADIALSAW It wilhin one year Irom the dale o! purchase, this Craltsman Radial Saw fails due to a delect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE AVAILABLE SIMPLY CONTACTING NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT...
Page 3 Safety Information The operator's manual contains safety infor- Major Hazards mation, instructions and signs for your protec- tion against serious injuries, including: 1. Workpiece Kickback Loss of fingers, hand, arm or leg from contact Kickback is an uncontrolled grabbing with the saw blade. throwing of the workpiece during...
Page 4: Location And Function Of Controls
3. Wrong Way Feed Wrong way feed is feeding the workpiece into the end of the saw with the anti-kickback pawls. The work_iece can be grabbed by the be blinded. blade and pull your hands into the blade before you can let go or pull back. Fingers, Wear safety...
Page 5 Safety Personal Safety 1. Wear safety goggles labeled "ANSI Z87.1" 1. Keep guards and anti-kickback pawls in on the package. Do not wear regular glasses, place and in working order. they are not safety glasses. 2. Check for broken or damaged parts before using saw.
Page 6 14. Rip workpieces that are longer than the 5. Do not overtighten the blade; the blade diameter of the blade being used. Do not rip collar can be warped. a workpiece that is shorter than the diameter of the blade being used. Safety Labels on the Radial Arm Saw...
Page 7 Putting Your Saw Together Your radial arm saw is easy to put together, The following parts are included with model however it will take time. Ask a friend to 113.197210: help, and follow these assembly instructions. It is important for your safety, and for the A Basic Saw Assembly ....
Page 8 The following parts are included with model 113.197250: MEDIUM SCREWDRIVER Basic Saw Assembly .... Rear Table ....7/16" WRENCH #2 PHILLIPS SCREWDRIVER 1/2" WRENCH Table Spacer ....Rip Fence ...... Front Table ....314" WRENCH HAMMER Operators Manual ....314" SOCKET 9/16"...
Page 9 AF Hex Hd. Screw 5/16-18 x 3/4 ..AG Washer 11/32x 7/8x 1/16 ..Lockwasher 5/16 ....Hex Nut 5/16-18 ....Pan Hd. Screw 1/4-20 x 1 ..Washer 17/64 x 5/8 x 1/32 ..Lockwasher ....AM Hex Nut 1/4-20 ....
Page 10: The Following Loose Parts Are Included Model
The following loose parts are included with model 113.197250: Leveling Feet ....Hex Nuts 3/8-16 ....Truss Head Bolts 1/4-20 x 1/2 ..BK Lockwashers 1/4 ....Hex Nuts 1/4-20 ....BM Hex Hd. Screw 5/16-18 x 3/4 ..BN Washer 11/32 x 7/8 x 1/16 ..
Page 11 4. As you assemble your radial arm saw, 1. Loosen the guard clamp screw and remove the guard from the motor. some of the holes in the parts will line up and others will not. This happens because some 2. Use the arbor wrenches to remove parts are used in other equipment or for other...
Page 12 11. Push the bevel lock to the left as far as it Right Side Panel ....will go. (Figure 13D) Left Side Panel ....Lower Shelf ....12. If there is a 1/16 inch gap or less between Skirt ......the bevel lock and the left side of the yoke Shelf Stiffener ....
Page 13 3. Put two truss head bolls through the shelf and each corner bracket to hold the brackets in place• 4. Put a lockwasher and hex nut on each bolt and tighten with a 7/16 inch wrench socket. 5. Put the shelf stiffener on the shelf and line up the holes.
Page 14 15. Attach two hinges to the right side panel 18. Put truss head bolts through the three above the spacer, using four truss head bolts, holes along the bottom edge of the right side lockwashers, and hex nuts. Tighten with a panel.
Page 15 Repeat steps 25-26 with the left spacer. Right Side Panel Rear Move the cabinet to the location where will use your saw. Put a hex nut on each of the leveling feet. (Figure Shelf Front Fig. 24 - Hex Nut for Leveling Foot Fig.
Page 16 35. Adjust the lower nut with the 9/16 inch wrench until the levelingJoot is at the desired height. Fig. 27 - Pan Head Screw 36. Tighten the top nut by hand. 37. Repeat steps 33-36 for the other three 3. Attach the door to the hinges on the side leveling feet if necessary.
Page 17 Mounting the Saw to Cabinet 1. Hold the saw by the front edge and the Fig. 32 - Support Bracket, LevelingFoot back of the column support, and lift it onto the cabinet. It may be necessary to have someone help you lift the saw. Make sure that four holes in the bottom of the saw line up with four holes in the top of the cabinet.
Page 18 Building the LEG SET 4. Mount the two front legs to the basic saw The following parts are used in the leg set assembly using truss head bolts, lockwashers, assembly: and nuts. However only put bolts through Legs ......sides of the saw assembly not the front.
Page 19 Truss Head _*_ Bolt 3. Loosen the top nut by hand. 4. Adjust the lower nut with the 9/16 inch wrench until the leveling foot is at the desired height. 5. Tighten the top nut by hand. 6. Repeat steps 8-11 for the other three leveling feet if necessary.
Page 20 Location and Function of Controls iii! i 113.197210 113.197250 Fig. 45 - Radial Saw Controls On/Off Switch _1_ WARNING: The saw can start ac- cidentally or be used by children others when the yellow key is left in the The on/off switch turns the power to the saw on and off.
Page 21 Bevel Lock The bevel lock is used to hold the blade at various angles to the table. To unlock the bevel lock, move the lock to the right. Always hold the motor when you unlock the bevel lock. (Figure 49) CAUTION: The motor is heavy and can swing...
Page 22: Ripping
swivel lock when the motor is in one of these There are five pre-set bevel angles at -90 °, -45 °, 0°, 45 °, and 90 °. To unlock the bevel positions, stand facing the saw handle, pull lock when the blade is at one of these angles, the swivel lock all the way toward you, and move the bevel lock all the way to the right...
Page 23: Crosscutting
Handwheel The handwheel controls the height of the radial arm. To raise the radial arm, turn the handwheel clockwise. To lower the radial arm, turn the handwheel counterclockwise. (Figure Fig. 55 - Handwheet One complete turn of the handwheel moves the arm !/16 inch.
Page 24 Alignment of the Blade ALIGNMENT OF THE BLADE IS THE 1. Use a 3/16 hex "L" wrench to loosen the MOST IMPORTANT STEP four screws in the front of the column ASSEMBLING YOUR RADIAL support. (Figure SAW. The blade of your radial arm saw must be aligned properly...
Page 25 Leveling Table Supports 1. Raise the radial arm until the bottom 6. Turn the motor until the arbor shaft is the motor is about 2-1/2 inches above the pointing straight down toward the saw. saw. (Figure 60) 2. Locate four hex head bolts and put a flat washer on each.
Page 26 If the arbor wrench will not fit between arbor shaft and the table support at any point, repeat steps 8-21 until the table supports level, or If there is a gap between the arbor wrench and the arbor shaft at any point, repeat steps 8-21 until the table supports...
Page 27 Mounting the Front Table !. Make sure that the front table is upside down. 2. Place a tee nut over the leveling hole and _" Set Screw hammer it into place. (Figure 63 & 64) Leveling Hole Bolt Tee Nut '_Pan Head Screw...
Page 28 8. Install the pan head bolts through the other 13. If there is a gap larger than 1/32 inch, go four mounting holes. Put a lockwasher back to step I 1 and repeat, hex nut on each bolt and tighten using a Phillips screwdriver.
Page 29 4. L: nlock the rip lock move the motor if the motor arbor moved away from until the motor arbor is over the front table. square, tighten the top right screw to move to the left. Then tighten the top left screw 5.
Page 30 18. Move the framing square towards motor arbor until the arbor and square touch each other. 19. Move the motor arbor back and forth along the radial arm. Do not move the square. 20. If the motor arbor just touches the edge the square at all points,...
Page 31 3. Place the arbor on the arbor shaft 6. "[urn the blade with your hand several times use the arbor wrenches to tighten. The arbor and check to see if the square is flush with blade. shaJt has left-handed threads, so you will have to turn...
Page 32 19. Turn the blade with your hand several 10. Hold the square in place and move times and check to see if the square is flush motor slowly until the square is flush with with the blade. blade. 11. Hold the motor tightly and lock the bevel 20.
Page 33 4. Turn the blade with your hand several times and check to see if the square is flush with the blade. 5. If the square is flush with the blade after each rotation, no change is needed. (Figure 85) Go to the next section, If there is a gap between the square and the...
Page 34 4. Turn the blade with your hand several Squaring Blade to Table for times and check to see if the square is flush Ripping with the blade. 1. Unlock the swivel lock and turn the motor 5. If the square is flush with the blade after to the out-rip position with the motor between each rotation...
Page 35 7. Hold the square in place and use the 9/16 hand. Try to keep the carriage bearing from turning. inch wrench to turn the bolt until the square is flush with the blade. 15. If you can keep either of the carriage bear- 8.
Page 36 Making Blade Parallel to Table These steps are done to help prevent workpiece from being thrown or damaged when the saw is used for edging. F_g.94 6. Lower the radial arm until the blade just rests on the edge of the framing square.
Page 37 9. Unlock the bevel lock. 14. Tighten the two screws on the back of the motor support. 10. Loosen the two screws on the back of the 15. Place the corner of the framing square motor support using a 3/16 inch hex-L wrench and pliers if necessary.
Page 38 WARNING: Kickback can occur if 3. Make sure that the lower edge of the guard the spreader is not in line with the is parallel to the table. (Figure 99 above) blade. You can be injured or killed. Al- ways adjust the spreader and make sure 4.
Page 39 13. Loosen both nuts on the spreader using a 1/2 inch wrench. Guard 14. Slide the spreader with your hand until it is against the fence directly behind the blade. Antikickback Pawls 15. Tighten both nuts using a 1/2 inch )reader wrench.
Page 40: Digital Display
Digital Display ELEV: This button displays the height of the blade. The "0" display is usually set with the blade just touching the table. A positive dis- play shows the distance the blade has been / CRRFTSMRN raised above "0". A negative display shows the distance the blade has been lowered...
Page 41 5. If there is still no display, contact your Installing the Battery nearest Sears store, or 1. Slide the battery into the opening behind If the display says: the digital display with the angled corner on top. (Figure 103) go to step 6. Battery 6.
Page 42 6. Unlock the miter lock. 7. Move the arm to the right until it snaps into the 45° position. 8. Lock the miter lock. 9. The display should say: l'" s.ol 10. Unlock the miter lock. 11. Move the arm to the left until it snaps Fig.
Page 43 Bevel Encoder 14. If the display is correct at all three points, go to the next section, 1. Push the ON/OFF button to turn the dis- play on. If the display is not correct at one or more of these points, go to step 15. 2.
Page 44 8. Push the ELEVbutton. If the display is still not correct, repeat steps 15 - 21 until the bevel encoder is in the 9. Push the REF SETbutton. right position, 10. The display will say: If the display is correct, go to the next section.
Page 45 go to the next section, 8. Lock the rip lock. 9. Push the RIP button. If the display says: 10. If the display shows the O-RIP function, .,P ! U.L! LI t J-I i-I I-! ] go to step 11, or If the display shows the RIP function, push push the REF SETbutton...
Page 46: Electrical Connections
Electrical Connections _l& WARNING: To avoid shock or fire, if Motor Specifications power cord is worn, cut, or damaged any way have it replaced immediately. The AC motor used in this saw is a capacitor- start, non-reversible type having the following Your unit is wired for 120V, it has a plug that specifications: looks like the one shown below.
Page 47 Extension Cords _lb WARNING: To maintain proper tool grounding, whenever the outlet you The use of any extension cord will cause are planning to use for this power tool some loss of power. Use the following table is of the two prong type do not remove to determine the minimum wire size...
Page 48 Crosscutting Crosscutting is used to cut a workpiece length. The workpiece is held against fence. The saw blade is pulled through workpiece. Cuts are usually made across the grain of the workpiece. Types of Crosscuts The basic types of crosscuts are shown below.
Page 49: Safety Information
4. Fingers or hand can slip into the saw Safety Information blade as you make a crosscut. Fingers, Crosscutting hand or arm can be cut off. Keep the hand holding the workpiece at least 8 in- Read and follow the safety information below ches to the side of the workpiece, out of...
Page 50: Cutting Accessories
10. The workpiece cannot be controlled Blade Guard, Anti-Kickback or held stable enough to do free hand Pawls and Spreader cutting. The workpiece can be thrown or slip and pull fingers and hand into the The blade guard, anti-kickback pawls and saw blade.
Page 51: Helpful Hints
Cutting Table and Fence Crosscutting Checklist Kerfs the following checklist at the beginning You will need to cut a new table kerf (shal- of each new cutting period to reduce the risk low cut) and fence kerf (slot left in the fence of an accident.
Page 52 WARNING: The saw blade will sud- 8. Grasp saw handle and hold your forearm in line with the saw handle as shown below. denly come toward you when lowered into the table if the rip lock is unlocked. Fingers and hand can be cut off. Lock the rip lock before and after each crosscut.
Page 53 4. Adjust the height of the anti-kickback Making Crosscuts pawls to clear top of fence and workpieee about 1/8 inch. The pawls and spreader help The following section contains safety informa- provide protection from the leading edge of tion and instructions for making crosscuts.
Page 54 Pull the saw blade through 12. Support hold the workpiece down and against the fence firmly with your left workpiece to the distance shown below. hand. 13. Pull blade through fence and workpiece just enough to complete the cut. (Fig. 120) 14.
Page 55 Ripping When to Use In-Rip or Out-Rip Ripping is used to change the width of the workpiece by sawing along its length. The The in-rip saw position provides better workpiece is fed into the saw blade. The visibility of both the workpiece and your fence is used as a guide.
Page 56 2. One of the most common and the Safety Information for most dangerous mistakes people make Ripping is to reach for the workpiece at the out- feed side of the saw. DON'T ! The Read and follow the safety information below workpiece could kickback...
Page 57 4. Non-thru cuts increase the chance 2. The workpiece can be grabbed by the kickback because the anti-kickback saw blade and take off like a missile. Anyone standing in the path of the pawls cannot always grab the irregular workpiece surface.
Page 58 Blade Guard, Anti-kickback Rip Cutting Checklist Pawls and Spreader Use the following rip cutting checklist at the The blade guard, anti-kickback pawls and beginning of each new cutting period workpiece spreader are designed to reduce reduce the risk of an accident. eliminate the risk of injury from blade con- tact, workpiece...
Page 59 Blade Guard Adjustments Making a Rip Cut Table Kerf 1. Unplug saw and remove yellow key. You will need to make a table kerr before rip cut can be made. Every time you move 2. Put saw in In-Rip position and lock the the blade a new distance from the fence, you...
Page 60 Making Rip Cuts Anti-kickback Pawls and Spreader Adjust- ments When to Use In-Rip or Out-Rip 1. Go to the outfeed end of the saw blade. The in-rip saw position provides better 2. Put edge of workpiece beside the blade visibility of both the workpiece and your and under...
Page 61 JlWARNING: When making through 9. Stand out of the line of the workpiece rip cuts do not set the blade closer than be clear of workpiece in case of kickback. 1/2 inch from the fence or auxiliary fence, your hands will be brought close to the blade.
Page 62 on the arbor could cause the dado and arbor nut to spin off. Take several passes of the dado if cut required is greater than 13/16 of Kickback, Blade Contact. an inch wide. Fingers, hand, 3. To avoid excessive load on the motor be cut off.
Page 63 41L WARNING: If the auxiliary fence 3. Remove saw blade, dado, or other acces- not used when the saw arm is in the 0 ° sory from the saw arbor shaft before using crosscut position, the molding head can- the accessory shaft.
Page 64 Cutting Accessories Fences Push Stick Fences are required for all saw operations. Push sticks are used during ripping when the blade is placed between 2 and 6 inches from the fence. Crosscutting requires fences with kerfs (slots) to match the path of the saw, because the saw Make a push...
Page 65 Auxiliary Fence and Push Block 2-1/4 An auxiliary fence must be used if the blade 314" Plywood is positioned between 1/2 inch and 2 inches from the fence during ripping. An auxiliary fence must always be used with a push block. This Face and This Their purpose is to keep your hands away...
Page 66 Auxiliary Fence for Edging 5. Cut out a notch from the 12 inch side of the 3/8 plywood that is 9 1/2 inches long by 3/8 Make an auxiliary fence for edging: inch wide. The dimensions of the remaining • before doing edging with the arm at 3/8 plywood are shown in Fig.
Page 67 Featherboard Featherboards are used during rip cutting to help keep the workpiece against the fence. The featherboard is clamped to the front table, so that the angled edge of the feather- board is against the workpiece on the infeed end of the blade. The other edge of the workpiece is against the fence.
Page 68 Sears Recommends The Following Accessories Item Cat. No. Saw blades (10" diameter with 5/8" hole) See Catalog 9-22221 or 9-22222 Leg Set Caster 9-25246 Sanding Drum See Catalog Drill Chuck Dust Collector See Catalog See Catalog Molding Head Guard 8" See Catalog Taper See Catalog...
Page 69 Lower Blade Guard Safety Information IMPORTANT _WARNING The following safety information and in- Remove the lower blade guard for ALL structions apply to all blades and accessories. other types of cuts except repetitive 90 ° crosscutting. Using the lower guard other The lower blade guard is required by the Oc- than for repetitive 90 °...
Page 70 Glossary Molding Cut: Non-through cut which Anti-kickback Pawls: Pivoted objects with produces a contoured surface on the teeth which help prevent workpiece kickback. workpiece. Arbor: The bar or shaft that holds the saw Outfeed: The end of the saw blade where the blade.
Page 71 Helpful Hints 3. Place the same edge of the workpiece In order to get accurate cutting results from against the fence for all cuts. Make the your radial arm saw, do the following: first cut at one end of the workpiece, then flip the workpiece over and make 1.
Page 72 To extend the life of the front table of your 3. Lock the miter, bevel, or swivel lock. saw, tack a piece of 1/4 inch plywood over it. Make sure that the tacks are not in the path of the saw blade. These steps will reduce stress on saw parts, and improve the accuracy of your cuts.
Page 73 Motor Frequently blowing of fuses or tripping circuit breakers result To avoid motor damage this motor should be blown out or vacuumed frequently to prevent • Motor is overloaded: Overloading can oc- sawdust buildup which will interfere with normal motor ventilation. cur if you feed too rapidly or if saw is mis- aligned so that the blade heels.
Page 74 Lubrication taining or lubricating your saw. Your saw is precision built and should be When you receive your new Craftsman radial kept properly lubricated. Before describing saw, it requires no lubrication. The radial the various points which may periodically re-...
Page 75 • Lubricate the cam surfaces of the rip lock assembly. • A light film of oil should be wiped on the face of the column tube to lubricate the fit between the column tube and column support. Turn the elevation handwheel to raise the arm to upper limit.
Page 76 Swivel Lock Adjustments for Wear This handle provides a friction lock between Bevel Lock the upper face of the yoke and the bottom face of the carriage. It should eliminate The purpose of the bevel lock is to lock the play or rotation between...
Page 77 Arm and Column With the miter lock unlocked and in the unin- dexed position the arm should fit snugly to the column tube and not allow any vertical movement. If you can move the end of the arm up and down an adjustment is needed.
Page 78 2. Push the carriage back against the rear stop. 3. Hold the front carriage bearing with your fingers as tight as possible and pull carriage forward at the same time. If you can prevent the bearing from turning an adjustment required.
Page 79 Rip Lock I_"' _Miter Lock Handle The rip lock locks the carriage in any position along the length of the arm. If the carriage can be easily moved by pushing and pulling on the yoke handle when the rip lock is in the locked position an adjustment is required.
Page 80: Trouble Shooting
Troubleshooting WARNING: To avoid injury turn power switch off and remove plug from power source outlet before troubleshooting. Electronics Problem Probable Cause What to Do Battery not installed correctly. Adjust battery position in com- No display when On/Off partment. button is pressed. Battery contacts dirty.
Page 81 Electronics - 2 What to Do Problem Probable Cause Display shows EEE.E or Arm or carriage moved Follow procedure for setting EE.EE. rapidly for indicator to monitor, zero reference points in the Set- ting Electronic Display section. Encoder or indicator display Have electronics checked Display will reset to zero...
Page 82 Motor - 2 What to Do Probable Cause Problem Reduce the line load. Power line overloaded with Motor fails to develop full lights, appliances, and other power. motors. (Power output of motor decreases rapidly with Increase wire sizes, or reduce Undersize wires or circuit too decrease...
Page 83 Saw Operations Problem Probable Cause What to Do Crosscuts accurate Looseness between column tube Go to Alignment of the Blade, 0 ° and 45 ° miter. and column support. Adjusting E_evation. Go to Alignment of the Blade, Crosscut travel not square with fence.
Page 84 Saw Operations What to Do Problem Probable Cause Saw blade not square Go to Alignment of the Blade, Workpiece kerr rough with tooth marks from to fence. Squaring Blade to Fence. blade (also called heel). Go to Alignment of the Blade, blade not parallel to table.
Page 85 Saw Operations What to Do Problem Probable Cause Clamping force not suffi- Bevel lock needs adjusting. Go to Maintaining Your Saw, cient at bevel angles other Adjustments for Wear, Bevel than 45 ° . Lock. Depth of cut varies from Table top not parallel with arm.
Page 86 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 (See Fig. 8) (See Fig.6) (See Fig. 2) (See Fig 3 & 4) (See F g. 7) (See Fig. 2) FIGURE...
Page 87 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE Part Part Description Description 816333-1 *Screw, Pan Rec. STD541025 "Nut, Hex 1/4-20 37384 Nut, Tee Type "'IT" 10-32 x 1/2...
Page 88 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 > FIGURE...
Page 89 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 2--BASE AND COLUMN ASSEMBLY Ke f Part Key] Part No. I Description Description ; ! 60339 9416187 Bolt, Hex Hd.
Page 90 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 MOTOR CORD FIGURE...
Page 91 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 3--YOKE MOTOR ASSEMBLY Part Part Description Description STD551012 *Washer, 17164 x 9t16 x 1/16 Yoke Assembly (see Figure 4)
Page 92 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113,197210 and 113.197250 ° FIGURE 4...
Page 93 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 4--YOKE ASSEMBLY Part Part Description Description 810214-3 Screw, Low Hd. STD551131 * Lockwasher, External 5/16 Cap 5/16-18 x 718...
Page 94 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 FIGURE 5...
Page 95 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 5--MOTOR ASSEMBLY Part I Key t Description 507744 Housing, Motor STD376116 *Capacitor 64950 Screw, Type "T" 64951 Screw, Flat Head...
Page 96 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 FIGURE 6...
Page 97 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 6--ARM ASSEMBLY Part Part Description Description 818239 Arm, Radial 818521 Bumper, Rubber 169123-2 Relief, Strain 816492 Clip, Wire Cable...
Page 98 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113,197250 FIGURE 7 - GUARD ASSEMBLY Always order by Part Number - Not by Key Number Par1 Part Description Description Guard 816264-1 STD581050 *Ring, Retaining 120399 "Nut, Square 5/16-18...
Page 99 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 Always order by Part Number - Not by Key Number FIGURE 8 - TABLE ASSEMBLY Keyl Part Description 818169 Table, Rear 818168 Table Spacer 63432 Fence, Rip...
Page 100 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 9--PARTS LIST 23" CABINET (MODEL 113.197210 ONLY) Part Part Description Description 815934 805589-5 Screw, Truss Hd Hinge, Door...
Page 101 PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL MODEL NOS. 113.197210 and 113.197250 Always order by Part Number--Not by Key Number FIGURE 10--LEG SET (MODEL 113.197250) Part Description 818213 818163 Channel, Leg 815909 Stiffener, Lower 818170 Bracket, Leg STD541237 *Nut, Hex Jam 3/8-16...
Page 102 NOTES...
Page 103 NOTES...
Page 104 SE_ARS 10-INCH ELECTRONIC Operators RADIAL SAW Manual SERVICE Now that you have purchased your 10-inch electronic radial saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.

This manual is also suitable for:

113.197210

Craftsman 113.197250 Operator's Manual

Quick Links

Related Manuals for Craftsman 113.197250

Summary of Contents for Craftsman 113.197250

This manual is also suitable for:

Table of Contents