Advertisement
Features,
Hints,
and Care
Follow
the
Colors
Your washer control panel is color
coordinated for your convenience.
When you set your washer controls,
notice which colors are the same. They
will help guide you through setting the
controls.
Need
more
Time?
Reset
the Timer
Knob.
Although wash cycles are automatic,
timer may be reset to lengthen, shorten,
or repeat a portion of a cycle.
To set or reset timer, push in timer knob
to stop washer. Hold in timer knob
firmly while slowly turning it to desired
setting. Pull out timer knob to start
washer.
Stops
and
Starts
Wash action consists of periods of
agitation, with pauses or periods of
soaking. For best results, do not turn
timer through pauses, which are normal
part of wash cycles.
Cleaner
Clothes
Water temperature affects how clean
clothes become. If your clothes are not
as clean as you would like, you may
need to raise the temperature on your
water heater. Check your water heater
manufacturer's recommendations,
as
well as local codes, for assistance. Also,
check that your water hoses are hooked
up correctly. If they are switched you
might be getting cold water in your
warm and hot cycles.
Hard
water
does not remove soil as
well as soft water. Check with your local
water company
to see if you have hard
water. If you have hard water, try
softening
it with a packaged
conditioner
or use a little more
detergent.
Risers
Risers or air cushions may be installed
if pipes knock or pound when flow of
water stops. Risers are more efficient
when installed as close as possible to
water supply faucets.
Lint
Filter
Amana's self cleaning lintfilter works throughout the wash cycle to constantly
remove lint and other residue from the water. Located between the outer and
inner tub, the lint filter removes lint as water passes from the bottom of the
outer tub back to the inner tub. As water passes from the outer tub to the
inner tub, water is forced through the bottom of the lint filter. The filter traps
lint under the filter until the spin cycle begins. During the spin cycle
centrifugal force removes the lint by pulling it off the bottom of the filter and
washing it down the drain.
Motor
Overload
Protector
Internal overload protector automatically stops motor in event of overload.
Overload protector resets in approximately 3 minutes and motor automatically
restarts. If overload protector stops motor again, stop using washer and call
service technician. Loading wash tub too full may result in motor overload.
Automatic
Balance
System
Your new washer will automatically adjust to unbalanced loads without
shutting down or interrupting the cycle. The cycle will automatically complete
contain excessive moisture. If this should happen,
simply redistribute the clothes, and reset the control to
the spin mark after the rinse setting in the regular cycle.
at the fastest spin speed possible.
__i
In a severe out-of-balance
condition, clothes may
E
Safety
Lid
Switch
The washer will not spin when the lid is open for any reason. This is for your
personal safety. If the lid is opened mid-cycle, operation will automatically
start when lid is closed.
General
Washer
Care
• Use only damp or sudsy cloth for cleaning control panel. Some cleaning
product sprays may harm control panel finish or may damage interior of
hood.
• Wipe washer cabinet as needed. If detergent, bleach, or other washing
products are spilled on cabinet, wipe immediately. Some products will
cause permanent damage if spilled on cabinet.
• Top of washer should not be used for removing garment stains. Some stain
removers, such as rust remover, may damage cabinet finish.
• Do not use scouring pads or abrasive cleansers.
• Do not lay sharp or rough objects on or against washer. Finish could be
damaged.
• Remove pins, buckles, or other sharp objects from clothes to prevent
scratching interior parts.
• Leave lid open after use to allow inside of washer to dry, and to help
prevent musty odors from developing.
• Do not allow small children to play on or around washer.
• Do not move washer without reinstalling shipping brace (Part #40068201 )
and shipping plug (Part #40047301 ). See Moving Washer to New Location
section.
9
Advertisement
