Switching Effect Modules On And Off; Storing A Patch - Zoom Player 1010 Operation Manual

The indicator of the effect module currently selected for
editing is flashing.
With each push of the MODULE SELECT
NOTE
edited module moves one position to the right. When the
REV/DLY module is reached, the cursor loops back to
the COMP&WAH module.
MODULE MODULE
COMP
DIST
WAH
3. Next, use the PARAM SELECT
parameter within that module that you wish to edit.
The indicator of the selected parameter is flashing.
With each push of the PARAM SELECT key, the selected
NOTE
parameter moves one position down. When PARAM 4 is
reached, the cursor loops back to PARAM 1.
PARM
PARM
PARM
PARM
PARM
The value of the selected effect parameter is shown on
HINT HINT
the display. If the display shows only "
module is OFF. Set the effect module to ON before
editing, as described on page 8.
+ -
4. Use the VALUE /
value.
For details on the parameters of each effect module,
HINT
HINT
please refer to "Effect Types and Parameters" on pages 9
– 12.
Parameter setting changes made in this way are only
NOTE
temporary. If you return to the Play mode or select a
different patch without storing the new settings first, the
settings will be lost.
For details on how to store a patch, please refer to the
explanation at right.

Switching Effect Modules On and Off

In the Edit mode, effect modules can be turned on and off
independently.
1. Pressing a pedal corresponding to an effect module
that is currently on (module cursor indicator lit) turns
the effect module off. The indicator goes out.
2. Press the pedal again to turn the effect module back
on.
MODULE MODULE MODULE
CHO REVERB
EQ
FLG DELAY
key to select the
PARM
1
PARM
2
PARM
3
PARM
4
PARM
1
", the effect
keys to change the parameter
The EQ module cannot be switched off. To disable this
NOTE
module, set all parameters (PARAM 1 through PARAM
4) to the value "5".
key, the
The pedals 1 – 3 and the BANK pedal correspond to the
HINT HINT
following effect modules:
• BANK pedal: COMP&WAH
• Pedal 1:
MODULE
• Pedal 2:
COMP
• Pedal 3:
WAH
The effect module ON/OFF setting can also be stored as
part of a patch.

Storing a Patch

If an edited patch is not stored, the change will be lost when
another patch is selected. To preserve a setting, store the
patch as described below.
1.Press the STORE key in the Edit mode.
This activates the store standby condition.
HINT HINT Storing is possible also in the Play mode.
2.Choose the bank and patch number in which you want
to store the patch.
Use the BANK pedal to first select the bank and then
specify the patch number with the pedals 1 – 3.
Patches cannot be stored in the PRESET group. If a
NOTE
patch was chosen from the PRESET group, the store
destination will automatically become the USER group.
Specify a bank and patch number in the USER group.
3.If no bank and patch number is specified for a patch
selected from the USER group, the patch will be stored
in the original location.
If no bank and patch number is specified for a patch
selected from the PRESET group, the patch will be stored
in "A1" of the USER group.
When a patch is stored, the patch that was previously
HINT HINT
stored in that number will be overwritten (erased). Take
care not to erase a patch that you want to keep. When
wishing to restore all factory preset patches, please refer
to "Reinitializing the 1010 (Special Mode)" on page 13.
Restoring individual patches is not possible.
4.Press the STORE key again. The patch is stored, and
the 1010 reverts to the Play mode.
If the STORE key has not yet been pressed for the second
NOTE
time, you can use the EDIT key to cancel the store
process and return to the Play mode.
DISTORTION
CHO/FLG
REV/DLY