Related Manuals for GE Keypad Controller 45631
Summary of Contents for GE Keypad Controller 45631
- Page 1 45631 Wireless Lighting Control Keypad Controller Z-Wave Certified ® Wireless Lighting Control...
- Page 2 Introduction: Thank you for your purchase of a GE Z-Wave control ® device. Z-Wave technology is designed to automate lighting/home control and provide easy remote operation of all your Z-wave enabled devices. The GE Z-Wave product family includes a variety of devices to control lighting in your home.
- Page 3 Group/Scene buttons are numbered only in the instructions. The buttons on the Amber LEDs behind device are not numbered. buttons provide visual feedback Turns selected Group or Scene ON Press & Release to change to Scene mode After entering SETUP mode, use to Remove devices from a Group or Scene...
-
Page 4: Z-Wave Terminology
Z-WAVE TERMINOLOGY Home Control Network: Your controllers and every Z-Wave Primary Controller: This is the device you have added with the main device used to set up and primary controller are linked control your Z-Wave network. together into a wireless network. There can only be one primary Each device in your network has controller and it must be used to... - Page 5 Scene: Scenes are normally to Remove the insulating tabs before trying to program and use activity based lighting schemes. A Scene lets you establish preset the device. brightness levels for multiple Battery Use and Safety Z-Wave controlled lights and - Use only fresh batteries of the then control them with one required size and command.
- Page 6 2. Remove the small screw from battery life. Under normal operating the battery retainer door. Pull conditions, the batteries should last out on the top of the door (it is for approximately one year. LED hinged at the bottom). indicators behind the Group/Scene 3.
- Page 7 WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS Controlling Appliances: Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance, also an unintentional activation may occur if the wrong button on the remote is pressed.
-
Page 8: Type Of Construction
Effects of Home Construction on Wireless Range Between Z-Wave Enabled Devices. Note: The distances shown in the table below are typical examples. Actual performance in your home will vary. From the Remote (or repeating Z-Wave module) to destination device: Type of Construction Wood Frame Brick, Tile or w/Drywall... -
Page 9: Operation
Please Note: Z-Wave home control networks are designed to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby cams, wireless video devices and older cordless phones using the 900MHz frequency range may cause interference and limit Z-Wave functionality. Many 900MHz products have a switch to select channel “A”... - Page 10 The network information copied to this device depends upon the brand/type of primary controller you are using. If the primary controller is a GE brand hand-held remote, all of the device & network information plus the first 4 Groups and Scenes you created can be copied.
- Page 11 Press and release the Add button. Press and release the Group button. Press and release the right side (ON) of the Group/Scene button (1, 2, 3 or 4) that you wish to assign the device to. The Orange LED will start blinking. Press and release the button on the device you wish to add.
- Page 12 NOTE: Non-dimmable On/Off only lighting devices can be added to Scenes in either On or Off mode so as an example, the same light could be ON in Scene 1 and Off in Scene 2. Step 7 above is skipped when adding an On/Off only device to a Scene.
- Page 13 Turn the Group or Scene ON by Pressing and releasing the right side of the desired button. The amber LED will blink twice. a. When activating a Group, lights controlled by GE Z-Wave dimmers will turn on to their last brightness level. Other brands may act differently.
-
Page 14: Restoring Factory Defaults
Put the primary controller into device delete mode so that it can communicate with this secondary controller. Refer to the instruction manual for your primary controller on how to put it into this mode Press and hold Add and Remove buttons at the same time until the Orange LED blinks twice, then release. - Page 15 Keeping the controller awake: In order to extend battery life, the controller normally goes into stand-by mode (sleep) after approximately 10 seconds of inactivity (no button Presses). It may be desirable to keep the controller awake so that another controller can request Version or Manufacturer Specific information.
-
Page 16: Fcc Notice
FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 17: Specifications
Compliance with IC Rules and Regulations IC: 6924A-ZW5301 Jasco Products Company Model: 45631 / ZW5301 Object is subject to the following two conditions. 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. -
Page 18: Warranty
WARRANTY JASCO Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. - Page 20 45631-1 04/10 is a registered trademark of General Electric Company and is used under license to Jasco Products Company LLC, 10 E Memorial Rd., Oklahoma GE SmartHome ™ City, Oklahoma 73114 Made in China Hecho en China All brand names shown are trademarks of their respective owners.