Epson 7400 Unpacking And Setup Manual
Epson printer unpacking and setup guide model number: 9800,9400,7800,7400
Hide thumbs
Also See for 7400:
- Service manual (428 pages) ,
- Notice sheet (4 pages) ,
- User manual (393 pages)
Table of Contents
Advertisement
Quick Links
®
Unpacking and Setup Guide
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Checking the Contents. . . . . . . . . . . . . . . . . . . . . . 5
EPSON Stylus Pro 9800/9400 . . . . . . . . . . . . 5
EPSON Stylus Pro 7800/7400 . . . . . . . . . . . 11
Setting up the Printer . . . . . . . . . . . . . . . . . . . . . . . 17
Loading the Roll Paper . . . . . . . . . . . . . . . . . . . . . 19
Loading the Cut Sheet Media . . . . . . . . . . . . . . . 21
Connecting the Printer with Your Computer . . . . 24
Installing the Printer Software . . . . . . . . . . . . . . . . 26
Using the Online User's Guide . . . . . . . . . . . . . . . 27
1
Advertisement
Table of Contents
Related Manuals for Epson 7400
Summary of Contents for Epson 7400
-
Page 1: Table Of Contents
Unpacking and Assembling Setting up the Printer ..... . . 17 Loading the Roll Paper ..... 19 Loading the Cut Sheet Media . -
Page 2: Printer Parts
Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers. -
Page 3: Safety Instructions
❏ Use only the type of power source indicated on the printer's label. ❏ Do not use a damaged or frayed power cord. ❏ If you use an extension cord with the printer, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating. - Page 4 For United Kingdom Users Use of options EPSON (UK) Limited shall not be liable against any damages or problems arising from the use of any options or consumable products other than those designated as Original EPSON Products or EPSON Approved Products by EPSON (UK) Limited.
-
Page 5: Checking The Contents
Checking the Contents For EPSON Stylus Pro 9800/9400 only For EPSON Stylus Pro 7800/7400 only For EPSON Stylus Pro 9800/7800 only Power cord Roll paper spindle with the roll paper Ink cartridges Roll paper belt Gray attachments Paper guides Black Ink Conversion Kit... - Page 6 Caution: The printer unit is heavy and unwieldy. Have two people unpack the printer unit, and four people place the printer unit on top of the base unit. Parts: Base upright, left...
- Page 7 Tools: Hex wrench Hex socket head bolts (4) Wing nuts, spring washers, and washers(2) H is for connecting the printer unit to the base unit. Paper feed support films (5) Assembling the base unit Caution: Have two people working on either side to assemble the base unit (20.5 kg).
- Page 8 Note: When you place the printer on the base unit, match the right end square of the printer (shown as 4 in the illustration below) to the square of the same part of the base unit.
-
Page 9: Attaching The Paper Basket
4. Fasten the bottom of the printer and base unit with wing nut, spring washers, and washers (H). 5. Release the front casters and the stabilizer knobs and move the printer to the place of use (a short distance away). Lock the casters and extend the stabilizer knobs after moving. - Page 10 2. Turning the stitch side downward, spread the paper basket on the floor. 3. Holding the rear shaft, pass it under the horizontal struts. 4. Rotate the rear paper basket joints to enfold the bar that is not attached to the fabric. Insert the stanchion pins into the holes on the base upright left and right, as shown.
-
Page 11: Unpacking And Assembling
If you want to feed the paper backward with the Auto Take-up Reel Unit, remove the paper guides. ❏ If the printer is not used or if you want to move the printer, insert the upper basket hooks. Make sure... -
Page 12: Unpacking The Printer
❏ Place the printer on a desk. If you cannot place the printer on a desk, you will need the Stand. If you place your printer on a desk, follow the guidelines listed below. ❏ Choose a desk that can hold the printer weight (about 49 kg) and has a height of 600-800 mm from the floor. -
Page 13: Using The Stand
3. Lift the box up and away from the printer. Remove all the items from the hollow (A and B) on the rear side of the printer. Note: The ink cartridges included with your printer are primarily for initial setup. - Page 14 Accessories: Base bolts (4) Strut bolts (2) Hex socket head bolts with washers (10) Collars (2) Wing screws (2) Washers (2) Assembling the Stand Caution: Assembly requires two people. Be careful to match the right and left legs (R and L is engraved on the inner side of the base parts) and base parts.
- Page 15 Hold the printer at the indicated locations as shown. If the ink cartridges are installed, do not tip the printer at an angle. Otherwise, ink may leak from the cartridges. 1. Lock the two casters and extend the two stabilizer knobs underneath the base unit.
-
Page 16: Reusing The Packaging
Stand. Make sure the joints are positioned as shown (O). 4. Set 2 paper guides at the bottom of the printer as shown below, when you feed the paper forward or backward. -
Page 17: Setting Up The Printer
Setting up the Printer Connecting the Power Cord Note: Most illustrations shown in this section are for EPSON Stylus Pro 9800/9400, so they may vary in appearance from EPSON Stylus Pro 7800/7400. The instructions are the same, except as noted. - Page 18 4. Hold the ink cartridge with the arrow mark facing up and pointing to the rear of the printer, and then insert it in the slot until the corresponding ink mark is displayed on the LCD.
-
Page 19: Loading The Roll Paper
❏ Remove the maintenance tank ❏ Unplug the power cord ❏ Remove the ink cartridges Loading the Roll Paper To load the roll paper onto the printer, follow the instructions below. 1. Slide the movable flange off the end of the spindle. - Page 20 Caution: Do not set the paper lever to the released position while the Power light is flashing. Doing so may damage the printer. 7. Insert the paper into the paper insertion slot. 8. Pull the paper down through the paper insertion slot so that it comes out below.
-
Page 21: Loading The Cut Sheet Media
As much as possible, keep your fingers off the printable surface of the media, as fingerprints may reduce printout quality. 1. Make sure that the printer is on and the roll paper cover is closed. 2. Press the Paper Source l button repeatedly... - Page 22 Stopping and restarting printing may reduce the print quality. Caution: Do not leave the paper in the printer for a long period of time; its quality will deteriorate. We recommend that you remove the paper from the printer after printing.
- Page 23 READY appears on the LCD panel. Caution: Do not leave the paper in the printer for a long period of time; its quality will deteriorate. We recommend that you remove the paper from the printer after printing.
-
Page 24: Connecting The Printer With Your Computer
Mac OS X 10.2 or later Mac OS 9.x Using the Built-in USB Interface To connect the printer to a USB port, you need a standard shielded USB cable. To connect the printer to your computer using the built-in USB interface, follow the steps below. - Page 25 Using the Optional Interface Card The following optional Ethernet interface card lets you use your printer on a network. The Ethernet interface card automatically detects the protocols on your network, so you can print from Windows XP, Me, 98, and 2000, or Mac OS X and 9.x on an AppleTalk network.
-
Page 26: Installing The Printer Software
With background printing on, you can use your Macintosh while it is preparing a document for printing. In order to use the EPSON Monitor IV utility to manage print jobs, background printing must be turned on. 4. Close the Chooser. -
Page 27: Using The Online User's Guide
On Windows, you can also access the User’s Guide via the Start menu. Click Start, point to All Programs on Windows XP or Programs on Windows Me, 98, or 2000. Select EPSON, and then select ESPR7X9X User’s Guide. Note: To read the online guide, you must have Microsoft Internet Explorer 4.0 or later, or Netscape Navigator...