System Verification - HP rp7440 Service Manual

2. Issue the shutdown command with the appropriate command-line options.
The command-line options you specify dictate the way in which HP-UX is shut down,
whether the nPartition is rebooted, and whether any nPartition configuration changes take
place (for example, adding or removing cells).
Use the following list to choose an HP-UX shutdown option for your nPartition:
• Shut down HP-UX and halt the nPartition.
• Shut down HP-UX and reboot the nPartition.
Issue the shutdown -r command to shut down and reboot the nPartition.
• Perform a reboot for reconfiguration of the nPartition.
Issue the HP-UX shutdown -R command to perform a reboot for reconfiguration.
This shuts down HP-UX, reconfigures the nPartition if needed, and reboots the
nPartition.
• Reboot the nPartition and put it into the shutdown for reconfiguration state.
Use the HP-UX shutdown -R -H command to hold the nPartition in the shutdown
for reconfiguration state.
This leaves the nPartition and all its cells in an inactive state (the nPartition can be
reconfigured remotely), unless the normal behavior has been modified.
To reboot the nPartition, you must do so manually by using the BO command at the
management processor Command Menu.
If HP-UX is halted on the nPartition, thus not allowing you to use the shutdown command,
you can reboot or reset the nPartition by issuing commands from the management processor
Command Menu.

System Verification

The minimum firmware version supported at release of the HP 9000 rp7440 Server is rp8440 and
rp7440 Firmware Version 1.0.
After the system firmware is updated, use the management processor (MP) cm menu to verify
status using the sysrevcommand.
MP:CM> sysrev
IO_LPM-1
: CIO-0
0 : 000.000.000
001.005.000 FIRMWARE:Core IO
: B.002.005.008
: B.000.000.000
Cell 1 PDHC
042.006.000 - Active
Verify that the processors are reporting by using the management processor (MP) Main Menu
and using the in prcommand to display their status:
Main Menu: Enter command or menu > in prPROCESSOR INFORMATION
--- --------
0x0491 0x0401
1A
0x8900 0x0491
Idle
1068 MHz 0x8900
0x0401 Idle
Active Processors: 8 Partition Deconfigured Processors: 0
Cabinet firmware revision reportPROGRAMMABLE HARDWARE :System Backplane :
----------- -----------
-----------
CIO-1
CELL_LPM CELL_JTAG
000.000.000 000.000.000 - not installedCell 1 :
MP-0
ED-1 : 002.006.000Cell 0 - not installed
: B.023.003.031 - Active
IPF_FW :
Processor Cell Slot CPU
-------- --------
Active
1068 MHz 0x8900
0x0401 Idle
2B 1068 MHz
0x0491 0x0401
Partition Total Cells: 1
001.001.000
-----------
----------- -----------
CELL_PDH
: B.002.005.008 ED-0
: 000.000.000
PDHC :
004.080.000
Speed HVERSION
-------- --------------
0B 1068 MHz 0x8900
0x0491 0x0401 Idle
2A 1068
0x8900 0x0491 0x0401
Idle
Partition Total Processors: 8
001.000.000IO Backplane
001.001.001 001.001.001Core IO
001.002.000
----------- -----------
001.002.000
: 002.006.000
PDHC : B.000.000.000
: 000.000.000
B.022.002.003
Cab/
SVERSION CVERSION State
1 0/1 0A 1068
0x0491 0x0401
1B
MHz 0x8900 0x0491
Idle
3B 1068 MHz 0x8900
System Verification
GPM EMMUX
: IO_LPM-0
001.002.000
-----------Cell
001.002.000
MP-1
PDHC
PDC_FW :
---- ----
MHz 0x8900
Idle
1068 MHz
0x0401
3A
0x0491
Partition
183