Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BenQ Manuals
  4. Projector
  5. RS232 Commands
  6. Manual

BenQ RS232 Commands Manual

Hide thumbs Also See for RS232 Commands:

Advertisement

Quick Links

See also: Installation Manual
BenQ RS232 Commands
1

Advertisement

loading

Related Manuals for BenQ RS232 Commands

Summary of Contents for BenQ RS232 Commands

  • Page 1 BenQ RS232 Commands...
  • Page 2 Table of Content 1. RS232 Cable Requirement and Pin Assignment ............. 2 2. RS232 Connection ......................2 3. Interface Settings ......................3 4. Command Table ....................... 4...

  • Page 3: Rs232 Cable Requirement And Pin Assignment

    1. RS232 Cable Requirement and Pin Assignment Cable Requirement: (to be checked) RS232 pin assignment Description Description 2. RS232 Connection Below shows the illustration of connection between PC and Projector. Note:...

  • Page 4: Interface Settings

    Make sure that your computer and projector are turned before connection. Power on the computer first, and then plug the power cord of the projector. (It may cause Com port incorrect function, if you do not follow this instruction) Adapters may be necessary depending on the PC connected to this projector. 3.

  • Page 5: Command Table

    4. Command Table *Note: The available commands are different by model. (ex: source, audio settings, aspect ratio..etc), please refer to the user manual for the further information. Function Type Operation ASCII Write Power On <CR>*pow=on#<CR> Power Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR>...
  • Page 6 Read Audio pass Status <CR>*audiosour=?#<CR> Write Dynamic <CR>*appmod=dynamic#<CR> Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR> Write Living Room <CR>*appmod=livingroom#<CR> Write Game <CR>*appmod=game#<CR> Picture Mode Write Cinema <CR>*appmod=cine#<CR> Write Standard <CR>*appmod=std#<CR> Write User1 <CR>*appmod=user1#<CR> Write User2 <CR>*appmod=user2#<CR> Write User3 <CR>*appmod=user3#<CR>...
  • Page 7 Write Aspect 16:10 <CR>*asp=16:10#<CR> Write Aspect Auto <CR>*asp=AUTO#<CR> Write Aspect Real <CR>*asp=REAL#<CR> Write Aspect Letterbox <CR>*asp=LBOX#<CR> Write Aspect Wide <CR>*asp=WIDE#<CR> Write Aspect Anamorphic <CR>*asp=ANAM#<CR> Read Aspect Status <CR>*asp=?#<CR> Write Digital Zoom In <CR>*zoomI#<CR> Write Digital Zoom out <CR>*zoomO#<CR> Write Auto <CR>*auto#<CR>...
  • Page 8 Settings-Network Status Write Standby <CR>*standbymic=on#<CR> Settings-Microphone on Write Standby <CR>*standbymic=off#<CR> Settings-Microphone off Read <CR>*standbymic=?#<CR> Standby Settings-Microphone Status Write Standby Settings-Monitor <CR>*standbymnt=on#<CR> Out on Write Standby Settings-Monitor <CR>*standbymnt=off#<CR> Out off Read Standby Settings-Monitor <CR>*standbymnt=?#<CR> Out Status Write 2400 <CR>*baud=2400#<CR> Write 4800 <CR>*baud=4800#<CR>...
  • Page 9 Write Freeze On <CR>*freeze=on#<CR> Write Freeze Off <CR>*freeze=off#<CR> Read Freeze Status <CR>*freeze=?#<CR> Write Menu On <CR>*menu=on#<CR> Write Menu Off <CR>*menu=off#<CR> Write <CR>*up#<CR> Write Down <CR>*down#<CR> Write Right <CR>*right#<CR> Write Left <CR>*left#<CR> Write Enter <CR>*enter#<CR> Write 3D Sync Off <CR>*3d=off#<CR> Write 3D Sync Top Bottom <CR>*3d=tb#<CR>...
  • Page 10 Discovery-on Write AMX Device <CR>*amxdd=off#<CR> Discovery-off Read AMX Device Discovery <CR>*amxdd=?#<CR> Status Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR> Read High Altitude mode <CR>*Highaltitude=?#<CR> status...