Page 2
Furthermore, BENQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BENQ Corporation to notify any person of such revision or changes.
ATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REF- ERENCE . Safety Instructions Read this user’s guide before you operate your projector and save it for future reference. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
BenQ DX/S660 DX/S650 User’s Guide Warranty Limited Warranty BENQ warrants this product against any defects in material and workmanship, under nor- mal usage and storage. Exclusion to Warranty: The lamps are considered a consumable item and are warranted for 90 days or 500 hours, whichever occurs first. Proof of purchase date will be required with any warranty claim.
Shipping Contents The Projector is shipped with the cables required for connection to standard PC or laptop computers. Carefully unpack and verify that you have all the items shown below. If any of these items are missing, please contact personnel at the place of purchase.
Left and Right buttons will function as Keystone +/- hot keys. Press the Exit button to go back to the main menu. Press Exit again to leave the menu system. BenQ DX/S660 DX/S650 User’s Guide LAMP TEMP Source Selects signal sources from among...
BenQ DX/S660 DX/S650 User’s Guide Adjuster The projector is equipped with 2 quick-release adjuster feet. Push the buttons to adjust its tilt angle. Lift the projector up and press the adjuster button to release the adjuster. The adjuster will drop into position and be locked.
Remote Control Description The remote control sensors are located in the front/ back of the projector. The distance between the sensor and the remote control should not exceed 6 meters. Power Menu 3 Left/ Keystone - 4 Right/ Keystone +...
BenQ DX/S660 DX/S650 User’s Guide Installing or Replacing Batteries Push and slide the battery compartment lid in the direction shown. Caution Avoid excessive heat and humidity. There may be danger of an explosion if batteries are incorrectly replaced. Replace only with the same or equiva- lent type recommended by the manufacturer.
INSTALLATION Screen Size Place the projector at the required distance from the screen according to the desired picture size (see the table below). Screen Size (Max.) Diagonal A. Width (cm) 30.4 61.8 60.8 123.65 91.2 185.3 121.5 247.0 151.9 308.7 182.3...
Page 15
BenQ DX/S660 DX/S650 User’s Guide Connecting to Various Equipment It only takes a few seconds to connect your projector to your desktop or notebook computer, VCR, or other systems. However, a Mac adapter (an optional accessory) is needed for connection to Macintosh computers.
Press POWER to start the unit. The back-lit POWER key flashes green and stays green when the power is turned on. (When the power is turned off, there is a 60-second cooling period before the projector can be re-started.) Switch on all connected equipment.
To correct this, press KEYSTONE +/- (hot key) on the control panel of the projector or on the remote control, and then adjust the sliding bar labeled Keystone, as needed. Press + to correct keystoning at the top of the image.
Source Selection When several input sources are available, press the SOURCE key to make a selection from the control panel of the projector or the remote control. Projector Auto Menu System Press Menu for the main menu, and then press Menu again to select items in the sub-menu.
BenQ DX/S660 DX/S650 User’s Guide 1. Display Menu FUNCTION DESCRIPTION Corrects any keystoning of the image. Keystone Adjusts the brightness of the image. Brightness Adjusts the degree of difference between dark and light in the image. Contrast Adjusts to avoid the occurrence of flicker.
*This function is not available when the input mode is PC. Adjusts the image to make it appear more red or blue. Tint *This function is not available when the input mode is PC. BenQ DX/S660 DX/S650 User’s Guide DESCRIPTION 2. 4:3 3. 16:9...
BenQ DX/S660 DX/S650 User’s Guide 3. Source Menu FUNCTION Mirror Source Volume Treble Bass Mute Operation DESCRIPTION Default Rear screen projection Selects the input source from among PC, Video, S-Video, and YP Adjusts the volume level. Adjusts the treble level.
User logo Enables the user to define his/her own logo screen that will display during strat-up. Three modes are available: Default (BENQ logo), black screen and blue screen. Returns all settings to their factory preset values. Default Selects video mode.
BenQ DX/S660 DX/S650 User’s Guide 5. PIP Menu These functions are available only when the input mode is PC and the PIP source is Video or S-Video. FUNCTION PIP Source PIP Size PIP Position H. Position V. Position More Options...
Shutdown Press POWER and a warning message will appear. To turn off the projector, press POWER again. The fan will continue to run for approximately two minutes. Turn off the main power switch. Disconnect the power cord from the wall socket.
The LAMP indicator will light up if the lamp becomes too hot. Turn off the power and let the projector cool for 45 minutes. If the LAMP indicator is still red when turning the power on, please contact your dealer.
Lamp Replacement Caution To reduce the risk of electrical shock, always turn off the projector and dis- connect the power cord before changing the lamp. Press the POWER button to switch off the projector. Disconnect the power cord from the outlet and the projector.
BenQ DX/S660 DX/S650 User’s Guide Caution To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. To reduce the risk of injuries to fingers and damage to internal compo- nents, use caution when removing lamp glass that has shattered into sharp pieces.
210W lamp module ......... . 60.J3004.001 Ordering Parts or Getting Information For product information, product assistance, service information, or to order accessories, please see the BENQ corporation website at http://www.BenQ.com. BenQ DX/S660 DX/S650 User’s Guide Maintenance...
Select the correct video system. Adjust brightness, contrast, or saturation. Press Auto on the control panel of the projector or the remote control unit to get better picture quality. Adjust the focus. Reposition the unit to improve its projection angle.
TIME. CHANGE THE LAMP! OUT OF LAMP USAGE TIME. YOU HAVE TO CHANGE THE LAMP! BenQ DX/S660 DX/S650 User’s Guide Description Projector is searching for input. Projector has identified the input signal and is running the auto image adjustment function.
BenQ DX/S660 DX/S650 User’s Guide SPECIFICATIONS Projector Specifications Technical Specifications Note: All specifications are subject to change without notice. General Product name Model name Optical Display system Lens F/Number Lamp Electrical Power supply Power consumption Mechanical Dimensions Operating temperature range...