Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BenQ L710 Series
Summary of Contents for BenQ L710 Series
- Page 1 L710 Series Projector RS232 Command Control Installation Guide...
-
Page 2: Table Of Contents
Table of Contents Introduction ............................. 3 Wire arrangement ................................ 3 RS232 pin assignment ..............................3 Connections and communication settings ..................4 RS232 serial port with a crossover cable ....................... 4 Settings .................................. 4 RS232 via LAN ................................6 Settings .................................. 6 RS232 via HDBaseT .............................. -
Page 3: Introduction
Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions. -
Page 4: Connections And Communication Settings
Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a crossover cable D-Sub 9 pin (male) on a projector PC or laptop D-Sub 9 pin (female) Communication cable (crossover) Settings On-screen images in this document are for reference only. - Page 5 Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected. Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check...
-
Page 6: Rs232 Via Lan
RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. Input 8000 in the TCP port # field. - Page 7 Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200 bps Check the baud rate of the connected projector from its OSD menu. Data length 8 bit Parity check None Stop bit 1 bit Flow control None...
-
Page 8: Command Table
Command table Available features differ by projector specification, input sources, settings, etc.. Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set. Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. ... - Page 9 Write Volume + <CR>*vol=+#<CR> Write Volume - <CR>*vol=-#<CR> Write Volume level for <CR>*vol=value#<CR> customer Read Volume Status <CR>*vol=?#<CR> Write Mic. Volume + <CR>*micvol=+#<CR> Write Mic. Volume - <CR>*micvol=-#<CR> Read Mic. Volume Status <CR>*micvol=?#<CR> Write Audio pass Through off <CR>*audiosour=off#<CR> Write Audio-Computer1 <CR>*audiosour=RGB#<CR>...
- Page 10 CR> Write User1 <CR>*appmod=user1#<CR> Write User2 <CR>*appmod=user2#<CR> Write User3 <CR>*appmod=user3#<CR> Write ISF Day <CR>*appmod=isfday#<CR> Write ISF Night <CR>*appmod=isfnight#<CR> Write <CR>*appmod=threed#<CR> Read Picture Mode <CR>*appmod=?#<CR> Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=value#<CR> Read Contrast value <CR>*con=?#<CR>...
- Page 11 native Read Color Temperature Status <CR>*ct=?#<CR> Write Aspect 4:3 <CR>*asp=4:3#<CR> Write Aspect 16:6 <CR>*asp=16:6#<CR> Write Aspect 16:9 <CR>*asp=16:9#<CR> Write Aspect 16:10 <CR>*asp=16:10#<CR> Write Aspect Auto <CR>*asp=AUTO#<CR> Write Aspect Real <CR>*asp=REAL#<CR> Write Aspect Letterbox <CR>*asp=LBOX#<CR> Write Aspect Wide <CR>*asp=WIDE#<CR> Write Aspect Anamorphic <CR>*asp=ANAM#<CR>...
- Page 12 Decrease Write 4 Corners Top-Right-X <CR>*cornerfittrx=+#<CR> Increase Read 4 Corners Top-Right-X <CR>*cornerfittrx=?#<CR> Status Write 4 Corners Top-Right-Y <CR>*cornerfittry=-#<CR> Decrease Write 4 Corners Top-Right-Y <CR>*cornerfittry=+#<CR> Increase Read 4 Corners Top-Right-Y <CR>*cornerfittry=?#<CR> Status Write 4 Corners Bottom-Left-X <CR>*cornerfitblx=-#<CR> Decrease Write 4 Corners Bottom-Left-X <CR>*cornerfitblx=+#<CR>...
- Page 13 Write Auto <CR>*auto#<CR> Write Brilliant color on <CR>*BC=on#<CR> Write Brilliant color off <CR>*BC=off#<CR> Read Brilliant color status <CR>*BC=?#<CR> Write Reset picture settings <CR>*rstpicsetting#<CR> Write Projector Position-Front <CR>*pp=FT#<CR> Table Write Projector Position-Rear <CR>*pp=RE#<CR> Table Write Projector Position-Rear <CR>*pp=RC#<CR> Ceiling Write Projector Position-Front <CR>*pp=FC#<CR>...
- Page 14 Write Standby <CR>*standbynet=off#<CR> Settings-Network off Read Standby <CR>*standbynet=?#<CR> Settings-Network Status Write Standby <CR>*standbymic=on#<CR> Settings-Microphone on Write Standby <CR>*standbymic=off#<CR> Settings-Microphone off Read Standby <CR>*standbymic=?#<CR> Settings-Microphone Status Write Standby Settings-Monitor <CR>*standbymnt=on#<CR> Out on Write Standby Settings-Monitor <CR>*standbymnt=off#<CR> Out off Read Standby Settings-Monitor <CR>*standbymnt=?#<CR>...
- Page 15 mode R> Read Light level status for <CR>*lampcustom=?#<CR> custom mode Write (dual Dual Brightest <CR>* lampm =dualbr#<CR> lamps) Write (dual Dual Reliable <CR>* lampm =dualre#<CR> lamps) Write (dual Single Alternative <CR>* lampm =single#<CR> lamps) Write <CR>* lampm (dual Single Alternative Eco =singleeco#<CR>...
- Page 16 Write Back <CR>*back#<CR> Write Source Menu On <CR>*sourmenu=on#<CR> Write Source Menu Off <CR>*sourmenu=off#<CR> Read Source Menu Status <CR>*sourmenu=?#<CR> Write 3D Sync Off <CR>*3d=off#<CR> Write 3D Auto <CR>*3d=auto#<CR> Write 3D Sync Top Bottom <CR>*3d=tb#<CR> Write 3D Sync Frame Sequential <CR>*3d=fs#<CR> Write 3D Frame packing <CR>*3d=fp#<CR>...
- Page 17 Status Write Broadcasting on <CR>*broadcasting=on#<CR> Write Broadcasting off <CR>*broadcasting=off#<CR>...
- Page 18 BenQ.com © 2018 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.01-C...