Extension Cords - Craftsman 315.115070 Operator's Manual

Ri_htF&x 8/12/2004 4:56 PAGE 012/015 Fax Server
DOUBLE INSULATION is a safety conceptin electric
power tools, whicheliminates the need for the usual
three wire groundedpower cordand groundedsupply
system. Wherever there is electdc currentin the tool
there are two complete sets of insulation to pmteotthe
user. All exposed metal parts are isolatedfrom internal
metal motor componentswith pretectin 9 insulation
IMPORTANT -- Servicingof a tool w ith double
insulationrequiresextreme care and knowledgeof the
system and shouldbe performed only by a qualified
service tecnhician. For service we suggestyou return
the tool to your nearest Sears Store for repair, Always
use originalfactory replacement partswhen servicing.
parts may create a hazard or cause product
damage.
GENERAL
Only the parts shownon parts list, page 13, are
(ntendedto be repairedor replacedby the customer.
All other insulatlen parts represent system an andimportant shouldbe part serviced of thedouble only --'_
by a qualified Sears earvice technician.
Avoid using solventswhen cleaningplasticp_rta.Most
plasticsare susceptibleto varioustypos of commercial
solventsand maYcloths to remove dirt, carbon dust, be damaged by theiruse.etc. Use clean ,_
WARNING: Do not at any time let brake fluids,
contain chemicalsthat can damage, weaken, or
destroy plastic.
When alsctdc tools are used on fiberglass boats,
sports cars, wallboard, spackling compounds,or
plaster, if has been found that they are subjectto
acceleratedwear and passible prematurefailure, as
the fiberglasschipsand gdndingsare highlyabrasive
to bearings, brushes, commutators, arc.
Consequently it is not recommendedthat:this tool be
used for extended work on any fiberglassmaterial,
wallpoard,spacklingcompounds,or plaster. During
any use on these matedals, it is extremelyimported:
that the tool iscleaned frequentlyby blowing with an
air jet.
'=_ safe_ glasses: AIwaySwith side wARN|NG wear safety goggles, Orshield s during power
tool operation or when blowing dust. If operation
is dusty, also wear a dust mask.
EXTENSION CORDS
The use of any extension cord will cause some loss of
power. To keep the lossto a minimumand to preveht
tool overheating,use an extensioncordthat is heavy
enoughto cam/the current the toolwill draw.
A wire gauge size (A.W.G.) of at least 16 is
recommendedfor an extensioncord 100 feet or less in
length.When workJng outdoors,use an extensioncord
that is suitablefor outdoor use. The cord's jacket will
be markedWA.
the sanding CAUTION :area and extension positionC°rds the cord away sofrom that it Keep
will not get caughton lumber, tools, etc., during
sandingor polishingoperation.
each use. If damagedCheck extensionreptaceWARNING: cords beforeimmediately '
Never use tool with a damaged cord since
touching the damaged area could cause
electricalshock resultingin serious injury.
LUBRICATION
All of the beadngs in this tool are lubdceted with a
sufficientamount of high grade lubricantfor the life of
the unit under normal opemtir,_j conditions.Therefore,
no furtherlubrication is required.
THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENTLY AVAILABLE AT SEARS RETAIL STORES
Polishing Bonnet
A
Assorted Sanding Discs
150 Grit -- Fine
100 Grit -- Medium
60 Grit -- Coarse
40 Grit -- VeW Coarse
WARNING:
The use of attachments or accessories not listed above might be hazardous.
11