Advertisement
Sears
OWNERS
MANUAL
MODEL NO.
315.11701
CAUTION
Read Rules for
Safe Operation
and Instructions
Carefully
SAVE THIS MANUAL
FOR FUTURE
REFERENCE
CRAFTSMAN
3 INCH
BELT SAN DER
DOUBLE
INSULATED
Introduction
Operation
Maintenance
Repair Parts
(UL)
%
,"
Designed
exclusively
for and sold only by SEARS. ROEBUCK AND CO., Chicago,
IL 60684 U.S.A.
2612547
182
PRINTED
IN
U.S,A
10-81
Advertisement
Table of Contents
Related Manuals for Craftsman 315.11701
Summary of Contents for Craftsman 315.11701
- Page 1 Sears OWNERS MANUAL MODEL NO. 315.11701 CRAFTSMAN CAUTION Read Rules for 3 INCH Safe Operation and Instructions BELT SAN DER Carefully DOUBLE INSULATED SAVE THIS MANUAL FOR FUTURE REFERENCE Introduction Operation Maintenance Repair Parts (UL) ," Designed exclusively for and sold only by SEARS. ROEBUCK AND CO., Chicago, IL 60684 U.S.A.
- Page 2 FULL ONE YEAR WARRANTY ON CR_AFTSMAN B_.LT SANDER If this Craftsman Belt Sander fails to give complete satisfaction within one year from the date of pur- chase RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears will repair it, free of charge.
- Page 3 RULES FOR SAFE OPERATION (Continued) face or dust mask if cutting 11. USE SAFETY GLASSES with tools. Also operation is dusty. 12. DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges.
-
Page 4: Switch
OPERATION WARNING: YOUR SANDER SHOULD NEVER CONNECTED TO POWER SUPPLY WHEN YOU ARE ASSEMBLING PARTS PERFORMING MAINTENANCE. DATA PLATE If any parts are missing do not operate your Sander FRONT until the missing parts are replaced. HANDLE Before attempting to use your Sander, familiarize yourself... -
Page 5: Installing And Adjusting Sanding Belt
OPERATION WARNING: ALWAYS WEAR SAFETY GLASSES OR EYESHIELDS WHEN OPERATING YOUR SANDER. IF THE SANDING OPERATION IS DUSTY, ALSO WEAR A FACE OR DUST MASK. FAILURE TO DO SO COULD RESULT IN DUST OR LOOSE PARTICLES BEING THROWN INTO YOUR EYES, RESULTING IN POSSIBLE SERIOUS INJURY. -
Page 6: To Operate
OPERATION TO OPERATE Clamp or otherwise secure the work to prevent from moving under Sander. WARNING: UNSECURED WORK COULD BE THROWN BACK TOWARD OPERATOR CAUSING INJURY. Before placing Sander on work surface, press the trigger switch and let the motor reach its maximum speed, then lower the Sander to the work surface with a... -
Page 7: Timing Belt Replacement
MAINTENANCE TIMING BELT REPLACEMENT DISCONNECT SANDER FROM POWER SUPPLY BEFORE SERVICING WARNING: WHEN REPLACING TIMING BELT, USE REPLACEMENT BELT NUMBER 990077.001 ONLY. See Key Number 5 on Parts List, Page 11. FAILURE TO DO SO WILL INTERFERE WITH THE INSULA. TION SYSTEM AND THE PERFORMANCE OF THE TOOL, CAUSING THE BELT TO SLIP AND WEAR EX-... - Page 8 NOTES Page 8...
- Page 9 NOTES Page 9...
-
Page 10: Parts Layout
CRAFTSMAN 3 INCH BELT SAN,IER -- MODEL NUMBER 315.11701 NOTE "A" PAGE 11 FOR PARTS LIST -- SEE PAGE 11 Page 10... -
Page 11: Belt Sander
CRI:iFTSIqI:IN" Sears 3 INCH OWNERS BELT SANDER MANUAL DOUBLE INSULATED SERVICE that have purchased your. Belt Sander, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts...