Chapter 9 List Of Error Message - Brother BES-1241BC Instruction Manual

Chapter 9 List of Error Messages
Code Error Messages
Main shaft stop position sensor
E-A8
error
E-B0 Lower shaft CPU error
E-B1 Thread jammed in rotary hook
E-B2 Hook motor origin point error
E-B3 Hook motor standby position error
E-B4 Hook motor standby position error
E-B5 Hook motor communication error
E-B6 Hook motor parameter error
E-B7 Hook motor overheat error
Hook motor overcurrent error
E-B8
Turn off the power
Thread trimming motor origin
E-B9
point error
E-BA Power supply frequency error
E-BC No power error
E-BD Lower shaft flash memory error
E-BE Lower shaft version-up error
E-BF ERROR BF
E-C1 ERROR C1
E-C2 Wiper out error
E-C3 ERROR C3
E-C4 Presser foot down error
E-C5 ERROR C5
E-C6 ERROR C6
E-C7 ERROR C7
E-C8 ERROR C8
E-C9 Embroidering start error
E-CA ERROR CA
E-CB Spindle rotation speed error
E-CD ERROR CD
E-CE Cylinder bed position error
E-CF ERROR CF
162
Error
Main shaft stop position signal error
Lower shaft CPU error
Thread tangle in rotary hook
Hook motor origin point error
Hook motor standby position error
Hook motor motor mode error
Hook motor communication error
Hook motor parameter error
Hook motor overheat error
Hook motor overcurrent error
Thread trimming motor zero point error
Power supply frequency error
No power error
Lower shaft flash memory error
Lower shaft version-up error
Lower shaft motor undefined error
Area over during embroidering
Wiper out error
Embroidering data buffer empty
Presser foot down error
Measured voltage value could not be received
form the lower shaft motor CPU.
Voltage value could not be transferred to the
lower shaft motor CPU.
Lower shaft error
Hook motor origin point error
Embroidering start error
No sewing permisson
Spindle rotation speed error
Speed command can not be received.
Cylinder bed position error
Rated voltage value could not be received from
the lower shaft motor CPU.
BES-941BC • BES-1241BC
Measures
Adjust the pulley stop position (100 degrees) above the needle
and press the . If the error occurs frequently, the parts
STOP
related to the main shaft stop position sensor are faulty.
This is not usually displayed.
Check to see that no lint is tangled in the rotary hook and press
the or turn on the F/B switch on the head to either side.
STOP
The rotary hook may be rotated forcefully. Press the
turn on F/B switch on the head to either side to cancel the
error. If the same error occurs again, the lower shaft sensor
is improperly adjusted.
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the lower shaft motor is faulty.
Turn the power off and check the thread trimmer and turn the
power on again. If it occurs again, the thread trimmer is faulty.
Turn the power off and on once. If the same error occurs
again, the power PCB or power supply is faulty.
It may usually occur momentarily when turning off the ma-
chine. If it occurs when the machine is on, it is a power failure
detection error.
Turn the power off and on once. If the same error occurs
again, the main PCB is faulty.
Press the or turn on the F/B switch on the head to either
STOP
side to cancel the error and upgrade the version again.
This is not usually displayed.
Set the embroidering area again on the panel.
If the wiper is tangled with a thread, remove it. Press the
or turn on the F/B switch on the head to either side.
This is not usually displayed.
Press the or turn on the F/B switch on the head to ei-
STOP
ther side. If the same error occurs again, adjust the
presser foot switch.
This is not usually displayed.
This is not usually displayed.
The machine may be being tested in the BC test mode. Exit
the test mode or turn the power off and on once. If the same
error occurs again, the main PCB is faulty.
Check the operation of the main shaft brake and the stop posi-
tion of the main shaft (100 degrees).
This is not usually displayed.
This is not usually displayed.
Press the or turn on the F/B switch on the head to either side
STOP
to cancel the error and press the
again, there is a possibility that the spindle is overloaded.
Turn the power off and on once. If the same error occurs
again, the main PCB is faulty.
Secure the bed. If the bed is secured, the bed sensor position
may be faulty. Readjust it.
Turn the power off and on once. If the same error occurs
again, the main PCB is faulty.
or
STOP
STOP
. If the same error occurs