Hotpoint RGB790WEKWW - Gas Range Owner's Manual page 41

Installation instructions
[] ELECTRICAL CONNECTIONS (CONT.)
B. Usage Situations where Appliance Power Cord will be
Disconnected Frequently.
Do not use :m adapter plug in these situations because
disconnecting of the power cold places undue strain on
the adapter and leads to e\vnmal fifilure (ff the adapter
ground terminal. The customer should have the 2-prong
wall receptacle replaced with a three-prong (grounding)
receptacle by a qualified electridan befbre using the
appliance.
The installation (ff appliances designed for mobile home
installation must confln'm with the Manufitctm'ed
Home Construction and Safety Standard, Tide 24 CFR,
Pai_ 3280 (flmnerly the Federal Standard tor Mobile
Home Construction and Saiety, Title 24, HLID, Part 280)
oi; when such standard is not applicable, the Standard
fbr Manufitctured Home lustallafious, latest edition
(Manuflicmred Home Sites, Commmfities and Set-Lips),
ANSI A225.1, latest edition, or with local codes. In
Canada, mobile home iusmllafion lnUSt be in accordance
with the current CAN/CSA Z240/MH Mobile Home
lustallation Code.
Electric Disconnect
[] Locate disomnect plug on tile range back.
[] Pinch sides ot com, ector and pull out of range back.
[] SEAL THE OPENINGS
Seal any openings in the wall behind the range and in
the floor under the range when hookups are completed.
[] CHECK IGNITION OF SURFACE
BURNERS
Operation of all cooktop and oxen burners should be
checked aftei the i ange and g_s supp b lines hme been
carefidh checked fbr leaks.
1?3ectric Ignition Models
Select a top burne* knob and sinmlmneous b push in and
turn to LITE position. 5bu will hear a clicking sound
indicating proper operation of the spark module. Once the
air has been purged fl'om the suppl} lines, burners should
light wflhin 4 seconds. After burner lights, romm knob ()tit of
the LITE position. Tr_ each burner in succession until all
burners hme been checked.
Quality of Flames
The combustion qua]d} of burner drones needs to be
determined _isuNh.
(A) Yellow flames--
Call for service
(B) Yellow tips on
outer cones--
Normal for LP gas
(C) Soft blue
flames--Normal for
natural gas
If burner flames look like (A), call for service. Normal
burner flames should look like (B) or (C), depending
on the type of gas you use.
Widl LP gas, some yelh)w tipping on outer cones is normal.
[] CHECK IGNITION OF OVEN BURNER
The oxen is desig_led to ot)eram quietl} and m_tomafically.
To ot)erate the oxen, press the BAI_ pad ml(t then press the
number pads until 350 ° at)t)ea_ in the display. Touch the
START/ON t)ad. After 30-90 seconds, the oven burner will
ig_fim and burn until the set mmpelature is reached. The
oxen bm'ner will continue to cycle on and off as necessary to
maintain the oxen at the mml)emture indicamd b) the displa)
To check ig_fition of tile broil burnei; touch tl_e BROIL
HI/tO pad and then the START/ON pad. After 30-90
seconds, the broil burner will ig_fim.
Electric ignition models require electrical power to ot)eram.
In c_tse of a p(_wer oumge, the oxen burne_ on these models
cmmot be lit mammlh with a match. Gas will not f]()_aunless
the g]o_ bin" is hot.
If the oxen is in use >,hen a power oumge occm% the
btlrner
will shut off and camlot be re-lit tmfil power is restored.
41