Headphones; Powering On; System Specifications; Troubleshooting Tips - Altec Lansing 251 User Manual

Headphones

To use headphones with the system, plug them into the labeled
jack on the front of the right satellite. When headphones are
connected, all satellites and the subwoofer are muted.

Powering On

1. After all other connections are made, plug the power cord (on the
back of subwoofer) into an AC wall socket. The speaker system is
now ready to operate.
2. Turn on the audio source.
3. Turn on the Altec Lansing 251 speaker system by pushing the On/Off
button located on the front of the right satellite. A green LED will
light next to the button when the power is ON.
NOTE: Consumers who purchased a 220V or 230V unit, need to ensure
that the power switch, located on the rear of the subwoofer, is in the
ON position.
If the power switch on the rear of the subwoofer is in the OFF position,
the entire unit is shut off.

System Specifications

Total System Power: 90 Watts (45 Watts RMS)
Frequency Response: 35 Hz - 18 kHz
Signal to Noise Ratio @ 1 kHz input: > 70 dB
Crossover Frequency: 150 Hz
System THD (distortion): < 0.50 % THD @ -10 dB full-
scale input voltage
Input Impedance: 10k ohms
SATELLITE AMPLIFIED SPEAKERS
Drivers (per satellite): One 3" full-range driver

TROUBLESHOOTING TIPS

The answers to most setup and performance questions can be found in
the Troubleshooting guide. You can also consult the FAQs in the
customer support section of our Web site at www.alteclansing.com. If
you still can't find the information you need, please call our customer
service team for assistance before returning the speakers to your
retailer under their return policy.
Customer service is available 7 days a week for your convenience. Our
business hours are:
Monday to Friday: 8:00 a.m. to 12:00 midnight EST
Saturday & Sunday: 9:00 a.m. to 5:00 p.m. EST
1-800-ALTEC-88 (1-800-258-3288)
Email: csupport@alteclansing.com
For the most up-to-date information, be sure to check our Web site at
www.alteclansing.com.
© 2002 Altec Lansing Technologies, Inc.
Designed and engineered in the USA and manufactured in our ISO9002
certified factory. United States Patents 4429181 and 4625328 plus other
patents pending.
MASTER VOLUME
The volume knob on the front of the right satellite is the master
volume control for the speaker system. Turn the knob clockwise to
increase the volume and counter-clockwise to decrease the volume.
SURROUND VOLUME CONTROL
The SURROUND control varies the volume of the left and right
surround speakers. Adjust this control as necessary to create the
optimum sound.The Surround Volume Control operates in the same
manner even on computers that only have stereo outputs.
CENTER VOLUME CONTROL
The CENTER control varies the volume of the center speaker. Adjust
this speaker as necessary to achieve a balanced sound.
SUBWOOFER LEVEL
The Subwoofer Level is located on the back of the subwoofer. Rotating
this control clockwise increases the bass while rotating the control
counter-clockwise decreases the bass. Blend the subwoofer output with
that of the satellites to set the correct volume.
SUBWOOFER
Speaker Drivers: One 5.25 " long-throw woofer
POWER REQUIREMENTS
USA/Canada/and applicable 120 V AC @ 60 Hz
Latin American countries:
Europe/United Kingdom; 230 V AC @ 50 Hz
applicable Asian countries;
Argentina, Chile and Uruguay:
ETL / cETL / CE / NOM / IRAM Approved
3
TROUBLESHOOTING TIPS
SYMPTOM POSSIBLE PROBLEM
No LEDs are lit. Power is not turned on.
AC cord is not connected to wall outlet.
Surge suppressor (if used) is not powered on.
Wall outlet not functioning.
No sound from Power isn't turned on.
one or more
speakers.
Volume setting is too low.
Audio cable isn't connected to audio source.
Audio cable is connected to wrong output on audio source.
Problem with audio source device.
No sound from Switch on the rear of the subwoofer is not in the
center or rear proper position.
satellites.
Rear or center level is set too low.
Crackling sound Bad connection.
from speakers.
Volume control in Windows is set too high.
A problem with your audio source device.
Sound is Volume level set too high.
distorted.
Windows volume control is set too high.
Sound source is distorted.
Radio Too close to a radio tower.
interference.
No sound from Subwoofer volume set too low.
subwoofer.
Sound source has little low-frequency content.
Low hum from The AC in your house is at 60 cycles per second, which is
subwoofer. within the audio frequency of the subwoofer.
Loud hum from Bad connection.
subwoofer.
Volume on your audio source device set too high.
Not enough bass Bass setting is too low.
from subwoofer.
Bad connection.
Too much bass Bass setting is too high.
from subwoofer.
Distorted Subwoofer too close to monitor.
monitor.
SOLUTION
Press Power button on the front of the right satellite.
Check to see if the "Power On" LED is illuminated on the rear of the
subwoofer. If not, connect AC power.
If the subwoofer's AC power cord is plugged into a surge protector, make sure
the surge protector is switched on.
Plug another device into the wall outlet (same jack) to verify the outlet is working.
Verify the subwoofer's AC power cord is plugged into the wall outlet.
Verify the Power button has been pressed and the green LED is illuminated.
Turn the volume knob clockwise to raise the volume.
Check volume level on the computer sound card or alternate audio source
device, and set at mid-level.
Check plug connections on both the subwoofer and source. Make sure the
signal cables are inserted firmly into the correct jacks.
Make sure the green 3.5 mm stereo cable is connected and fully inserted into
the "line-out" jack of the audio source.
Test the speakers on another audio device. Remove the green audio cable
from the audio source device and connect it to the "line-out" or headphone
jack of another audio source.
Change the position of the switch.
Increase the rear or center speaker volume level.
Check all cables. Make sure they are connected to "line-out" or "audio-out" jack on
your sound card or other audio source– NOT "speaker-out."
Check the Windows volume control and decrease if necessary.
Unplug the stereo cable from the audio source. Then plug it into the headphone
jack of an alternate audio source (e.g., Walkman, Discman or FM radio).
Decrease master volume level.
Adjust the Windows volume and balance controls to the center as a starting point,
then adjust the level on the speaker using the volume control.
.WAV files are often of poor quality. So distortion and noise are easily noticed
with high-powered speakers. Try a different sound source such as a music CD.
Move your speakers to see if the interference goes away. If not, you may be
able to purchase a shielded stereo cable from your local electronics store.
Adjust the bass level on the rear of the subwoofer.
Many .WAV and .MID files often have little low-frequency content and sound
flat when you listen to them on a computer. Try a song with more bass–
something from your CD collection.
Some low hum may be detected when your speaker system is powered on without
an audio source playing, or when the volume is set at an extremely low level.
Unplug the power cord from the surge protector (if used), and plug directly
into an AC wall outlet.
Move your cables. Check to ensure they are making a clear connection.
Disconnect your green stereo cable from the audio source. If the loud hum
goes away, lower the volume on the audio source.
Lower the master volume or bass level on your computer, portable device, etc.
Adjust the bass level on the subwoofer.
Check to make sure that all cables are connected properly and are making a
clear connection.
Decrease the bass level on the subwoofer.
Because the subwoofer is not magnetically shielded, it can cause distortion if it's too
close to your monitor. Move the subwoofer so it's at least 2 feet from your monitor.
4