Dimensions; Torque Requirements - Exmark Lazer Z XP Operator's Manual

2.10.8 Cutting Height Adjustment: an extra-long cushioned lever is used to adjust the
cutting height from 1 1/2" (3.8 cm) to 5" (10.2 cm.) in 1/4"(6.4 mm) increments.
The cutting height adjustment handle has a transport position and all adjustments
can be made while the operator remains seated. Units also have a foot operated
deck lift assist lever to aid in raising the deck.
2.10.9 Mulching Kit: Optional.

2.11 DIMENSIONS

2.11.1 Overall Width:
60" Deck
72" Deck
2.11.2 Overall Length:
60" Deck
72" Deck
2.11.3 Overall Height:
60" Deck
72" Deck
NOTE: Height will vary slightly depending on seat setting
2.11.4 Tread Width: (center to center of tires, widthwise)
60" Deck
72" Deck
2.11.5 Wheel Base: (center of caster to center of drive tire)
60" Deck
72" Deck
2.11.6 Curb Weight:
60" Deck
72" Deck

2.12 TORQUE REQUIREMENTS

Bolt Location
Cutter Housing Spindle Nut (secured with threadlocker) 140-145 ft-lbs. (190-197 N-m)
Blade Mounting Bolt ....................................................... 115-120 ft-lbs. (156-163 N-m)
Jack Shaft Spindle Nut ................................................... 75-80 ft-lbs. (102-108 N-m)
Engine Deck/Front Frame Mount ................................... 30-35 ft-lbs. (41-48 N-m)
Anti-Scalp Roller (See Figure 12)
Type A – Whizlock Nut .......................................... 40-45 ft-lbs. (54-61 N-m)
Type B – Nyloc Nut................................................ 30-35 ft-lbs. (41-47 N-m)
Type B – Hex Capscrew ........................................ 50-55 ft-lbs. (68-75 N-m)
Starter Mounting Bolts (M10).......................................... 22-27 ft-lbs. (30-37 N-m)
Water Separator Mounting Bolts (M8) ............................ 11-14 ft-lbs. (15-19 N-m)
Hydraulic Oil Filter Head Mounting Bolts (M6) ................ 60-72 in-lbs. (7-8 N-m)
Wheel Lug Nuts.............................................................. 90-95 ft-lbs. (122-129 N-m)
Wheel Motor Mounting Bolts .......................................... 72-77 ft-lbs. (98-104 N-m)
Wheel Hub Slotted Nut................................................... minimum125 ft-lbs. (169 N-m)
Rollover Protection System (Roll Bar) Mounting Bolts .... 30-35 ft-lbs. (41-47 N-m)
Clutch Retaining Bolt (secured with threadlocker) .......... 55-60 ft-lbs. (75-81 N-m)
without deck deflector up
54.5 in. (138.4 cm) 61.4 in. (156.0 cm)
58.5 in. (148.6 cm) 73.2 in. (185.9 cm)
Roll Bar – Up Roll Bar - Down
82.2 in. (208.8 cm) 92.3 in. (234.4 cm)
86.0 in. (218.4 cm) 96.1 in. (244.1 cm)
Roll Bar - Up Roll Bar - Down
73.7 in. (187.2 cm) 55.6 in. (141.2 cm)
73.7 in. (187.2 cm) 55.6 in. (141.2 cm)
Drive Wheels
42.8 in. (108.7 cm) 38.9 in. (98.8 cm)
46.8 in. (118.9 cm) 47.6 in. (120.9 cm)
54.0 in. (137.2 cm)
56.8 in. (144.3 cm)
1639 lbs. (743 kg)
1657 lbs. (752 kg)
- 13 -
deflector down
72.2 in. (183.4 cm)
84.3 in. (214.1 cm)
Casters
Torque