EverFocus EQ610 Operation Instructions Manual
  1. Manuals
  2. Brands
  3. EverFocus Manuals
  4. Security Camera
  5. EQ610
  6. Operation instructions manual

EverFocus EQ610 Operation Instructions Manual

1/3” color day/night plus wide dynamic range box style camera
Hide thumbs Also See for EQ610:
Table of Contents

Advertisement

Quick Links

See also: Quick Reference Manual
Please read this manual first for correct installation and operation. This manual should be retained for future
reference. The information in this manual was current when published. The manufacturer reserves the right
to revise and improve its products. All specifications are therefore subject to change without notice.
PRECAUTIONS
1.
Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio
speakers since the electromagnetic fields generated from these devices may distort the video image.
2.
Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other
damage.
3.
Try and avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits.
4.
Keep the power cord away from water and other liquids and never touch the power cord with
wet hands.
Touching a wet power cord with hands or touching the power cord with wet hands may result in electric
shock.
5.
Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in equipment failure, electric shock or, in extreme cases, fire.
6.
Cleaning
Do not touch the surface of the sensor directly with the hands. Use a damp soft cloth to remove any
dirt from the camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor
and the camera lens. Please do not use complex solvents, corrosive or abrasive agents for cleaning.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within 0℃ ~ 50℃ (32℉~122℉) and humidity between 20~80%.
The input power source is 12VDC/24VAC ; 100~240VAC or 12VDC only.
1/3" Color Day/Night
plus Wide Dynamic Range
Box Style Camera
Operation Instructions
Model No.
EQ610

Advertisement

Table of Contents
loading

Related Manuals for EverFocus EQ610

Summary of Contents for EverFocus EQ610

  • Page 1 1/3” Color Day/Night plus Wide Dynamic Range Box Style Camera Operation Instructions EQ610 Model No. Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS 1. PRODUCT OVERVIEW .......................3 1.1 Main Features ............................... 3 1.2 Package Contents............................3 1.3 Specifications ..............................4 2. NAMES AND FUNCTIONS OF PARTS ..................5 2.1 Front panel..............................5 2.2 Top/Bottom Mounting ............................. 5 2.3 Back panel and connections ........................... 6 3.
  • Page 3 5.6 DAY NIGHT..............................19 5.7 3DNR ................................. 20 5.8 SPECIAL ..............................20 5.8.1 CAM TITLE............................... 20 5.8.2 D-EFFECT ............................... 21 5.8.3 RS-485 ..............................22 5.8.4 MOTION ..............................22 5.8.5 PRIVACY ..............................23 5.8.6 SYNC ..............................23 5.8.7 LANGUAGE ............................. 23 5.8.8 RETURN..............................

  • Page 4: Product Overview

    Amazing color low light sensitivity of .05 lux before the added benefits of digital signal processing technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus EQ610. Color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions.

  • Page 5: Specifications

    1.3 Specifications Pickup Device 1/3" SONY Super HAD II CCD Video Format NTSC or PAL NTSC: 525 TV lines, 60 fields/sec; Scanning System PAL: 625 TV lines, 50 fields/sec. Picture Elements 768 x 494(NTSC); 752 x 582(PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2(AGC ON);0.0002Lux/F=1.2 (Sens-up 256x) S/N Ratio...

  • Page 6: Names And Functions Of Parts

    2. NAMES AND FUNCTIONS OF PARTS 2.1 Front panel Light Sensor TAKE CARE NOT TO OBSTRCUT THIS OPENING WITH THE BODY OF THE LENS! The light sensor is for optional control of D/N switching levels in some applications. See section 5.6 for details.

  • Page 7: Back Panel And Connections

    2.3 Back panel and connections 100~240VAC 12VDC only ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 24VAC/12VDC ○ ○ ○ ○ ○ ○ ○ ○ ○...
  • Page 8 Terminal Block ○ Terminal block connections: Connect wires to the terminal block by: strip the insulation back ½” from the end of the wire; press in on the upper tab above the lower wire opening; while holding the tab in, insert the wire; release the tab, pull back gently on the wire to lock it in, and the wire should be retained.
  • Page 9 Menu button for cursor left movement ○ Menu button for cursor up movement ○ Button to access on-screen setting menu and for SET command ○ Menu button for cursor right movement ○ Menu button for cursor down movement ○ Power LED ○...

  • Page 10: Installation

    3. INSTALLATION Unscrew/remove the cover cap from the lens mount. If C mount lens is used, please add the C adaptor mount ring (the 5mm thick ring in the accessory pack) between the lens and the mount. Please note: Failure to use a spacer ring when attaching a C mount lens can damage the camera! Mount the lens by turning it clockwise into the lens mount.

  • Page 11: Rs-485 Connection

    4. RS-485 CONNECTION Connect the cable from keyboard or DVR RS485 port to the camera’s RS485 port. Connect the cable from video output BNC of the camera to a monitor or DVR input BNC. The RS485 ID set in the OSD Menu on the camera has to be the same as CAM ID used by the keyboard or DVR to control this camera.

  • Page 12: Camera Setup Operations

    5. CAMERA SETUP OPERATIONS This camera utilizes an On Screen Display (OSD) user setup menu. 5.1 Setup Buttons To set items on the user setup menu, use the following buttons on the back panel. Left Button ○ Up Button ○ Set/Menu Button ○...

  • Page 13: Display/Close The User Setup Menu Screen

    5.2 Display/Close the user setup menu screen Set button The Cursor Buttons & the MENU/SET Button Press the SET button The menu screen will appear on the monitor. Using the cursor button Use the cursor buttons  or  to move the cursor up or down. Use the cursor buttons ...
  • Page 14 EQ610 Menu Tree - 13 -...
  • Page 15 - 14 -...
  • Page 16 - 15 -...

  • Page 17: Lens

    5.3 LENS 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. Please select the type of the lens used (Manual/DC type) by pressing the LEFT or RIGHT button. NOTE: The brightness of the screen can be adjusted in DC mode in LENS LEVEL.

  • Page 18: Sense-Up

    5.4.4 SENSE-UP SENSE-UP is used to keep a brilliant, vivid screen image under low light level conditions by automatically compensating for changes in the level of light. 1. Please direct the arrow to point to “SENSE-UP” by using the UP and DOWN buttons. 2.

  • Page 19: Blc/Hsblc

    HEIGHT: Set the height of an area for the BLC to be adjusted. The value adjustable is 0~6. RETURN: Press “RET” to save all settings in the BLC menu and return to the previous menu. Press “END” to save all the menu settings and exit. 5.4.6 BLC/HSBLC HSBLC Highlight Suppression BLC...

  • Page 20: Return

    5.4.8 Return Press “RET” to save all settings in the Exposure menu and return to the previous menu. Press “END” to save all the menu settings and exit. 5.5 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. 1.

  • Page 21: 3Dnr

    S-Level: Set the start level from 0~100. E-Level: Set the end level from 0~100. EXT: The picture can switch automatically to color in a normal environment and to B/W when the ambient illumination is low based on the illumination reaching a light sensor; or it may be directly controlled by a trigger voltage.

  • Page 22: D-Effect

    5.8.2 D-EFFECT 5.8.2.1 FREEZE (Note that practical application of this feature requires direct access to the camera menu in real time). -OFF: Select “OFF” to view moving pictures. -ON: Select “ON” to view still pictures. 5.8.2.2 MIRROR -OFF: Disable the effects. -MIRROR: Sets a horizontal image inversion.

  • Page 23: Rs-485

    additionally color reversed, with red areas appearing cyan, greens appearing magenta and blues appearing yellow. 5.8.2.6 RETURN Return: Press “RET” to save all settings in D-EFFECT menu and return to the previous menu. Press “END” to save all the menu settings and exit. 5.8.3 RS-485 -CAM ID: Select RS-485 ID from 1~255.

  • Page 24: Privacy

    5.8.5 PRIVACY This mode masks areas you do not want to display on the screen. -OFF: Disable the PRIVACY function. -ON: AREA SELECT: Please select the area you would like to hide from the 8 areas in AREA  SELECT mode AREA DISPLAY: Select “ON”...

  • Page 25: Return

    5.9.4 RETURN Press “RET” to saves all settings in the ADJUST menu and returns to the previous menu. Press “END” to save all the menu settings and exit. 5.10 RESET 5.10.1 FACTORY RESET Reset to the default settings. 5.10.2 RETURN Press “RET”...
  • Page 26 1801 Highland Ave. Unit A 415 Oser Ave Unit S Duarte, CA 91010 ,U.S.A Hauppauge, NY 11788 Tel: +1-626-844-8888 Sales: +1-631-436-5070 Fax: +1-626-844-8838 Fax: +1-631-436-5027 Ihr EverFocus Produkt wurde entwickelt und Your EverFocus product designed hergestellt qualitativ hochwertigen manufactured with high quality materials and Materialien und Komponenten, die recycelt und components which can be recycled and reused.

Table of Contents