LG 42700H - 42INCH CLASSHDTV Technical Manual page 99

COMMERCIAL MODE SETUP
N
0
_D
N
0
rll
c
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level
allowable with the VOLUME (VOL) Up/Down controls.
In this way, for example, someone can not set the vol-
ume level high enough to disturb others. The value
range is 0 to 63, with 63 as the default, which gives the
user the full range of volume control, if item 008 MIN
VOLUME is also set at 0. Change values with ADJ
Left/Right arrow keys. It may be best to set the same
value on every TV.
NOTE: The maximum volume level cannot have a value
setting lower than the MIN VOLUME level (described
previously).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to I,
sound cannot be muted. If set to 0, sound can be
muted.
011 - KEY DEFEAT (Keyboard Defeat)
If set to I, key defeat prevents the end user from
accessing the on-screen menus with the display front
panel--MENU, SELECT, and Left / Right arrow keys do
not function. If set to 0, those keys do function.
NOTE: The menus can always be accessed by pressing
MENU on the remote.
01S - SLEEP TIMER
If set to 1, the SLEEP TIMER feature may be used. If
set to O, the Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers) *
If set to I, Timer function is available to user and
enabled continuously. Set to 0 to disable On/Off
Timers. (Clock must be set in order to use Timers.)
017 - ALARM *
Gives the installer the option of making the Alarm
function available to the end user. If set to 1, Alarm
function is available to end user. Set to 0 to disable
the Alarm function.
NOTE: Clock must be set before the Alarm function
will work.
021 - V-CHIP (Parental Control) *
Set to 1 to activate V-Chip (Parental Control); have it
available to end user to filter and control or otherwise
restrict programming content that can appear. Set to 0
to turn V-Chip feature Off, not available to user; no
programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours) *
Sets hours from 0 to 99 for the maximum V-Chip
(Parental Control) block hours. Default setting is for
12 blocking hours.
* Only affects Function Menu if enabled by
some PPV providers.
023 - CAPTION LOCK
Set to 1 to restore previous caption On/Off state after
turn Off. If set to 0, captions are always Off at turn
On.
028 - CH. OVERIDE (Channel Override)
If set to I, the user can select channels with either
Channel up/down or by direct keypad entry. If set to
0, only those channels that are entered for scanning
can be selected.
029 - OLD OCV (On Command Video
TM)
Set to I for operation with systems from On
Command Corporation.
030 - ACK MASK
M.RI. Communication Parameter. Leave at default set-
ting unless changed by Pay-Per-View provider. When set
to I, changes M.RI. for some OCV boxes.
031 - POLL RATE
M.RI. Communication Parameter. Selects Poll Rate for
M.RI. Leave at default setting unless changed by Pay-
Per-View provider. Step size of 16 ms.
032 - TIMING PULSE
M.RI. Communication Parameter. Leave at default set-
ting unless changed by Pay-Per-View provider. Sets
baud rate. Step size of 4.3 uS.
034 - CAMPORT EN. (Camera Port Enable)
Set to I to enable Video 2 input on display panel. If
set to 0, Video 2 input on display panel is not func-
tional.
NOTE: S-Video overrides Video jack.
03S - COMPPORT EN. (Computer Port Enable)
Enable/disables display panel HDMII input jack. Set to
0 to disable, set to I to enable.
NOTE: The setting above is ignored if Installer item
093 RiP AVAILABLE, is set to I.
038 - YPrPb EN. (Rear Component Video Enable)
Set to I to enable display panel rear Component
Video input jacks.
Set to 0 to disable display panel rear Component
Video input jacks.
039 - REAR AUX EN. (Rear Aux Enable)
Set to I to enable display panel rear AUX (Video I ) input.
Set to 0 to disable display panel rear AUX (Video I )
input.
Note: S-Video overrides Video.
98