LG 42700H - 42INCH CLASSHDTV Technical Manual page 101

COMMERCIAL MODE SETUP
N
0
I'rl
N
0
I-I-I
I-I-I
-t
c
091 - YPrPb2 (HDMI2 Enable)
Set to 0 to disable display panel HDMI2 input.
Set to 1 to enable DTV mode. Set to 2 to enable PC
mode.
093 - RIP AVAILABLE (Remote Jack Pack Available)
0 = Remote jack pack is not available or disabled.
I = Legacy Model RJPs:HDMI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.
Video is from HDMI. Audio stream is expected from HDMI
source. If no audio is present, no audio will be heard.
2 = Legacy Model RJPs,DVI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.
Video is from HDMI however, Audio is from selected audio
source, based on the RJP'saudio hierarchical priority.
5 = Scaler Model RJPs, HDMI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.
Vldeo is from HDMI. Audio stream is expected from HDMI
source. If no audio is present, no audio will be heard.
6 = Scaler Model RJPs, DVI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.
Video is from HDMI however, Audio is from selected audio
source, based on the RJP'saudio hierarchical priority.
Notes :
See Reference section, RJP Input Hierarchy and RJP
Models page.
If set to I, 2, 5 or 6, item 040 Auto Camport is auto-
matically set to 0.
Settings I, 2, 5 and 6 allow the lodge staff to customize
each TV's RJP setup based on customer requirements.
094 - SAP MENU EN (2rid Audio Program)
Set to 1 to enable SAP feature on Function menu, if
Function menu is available.
Set to 0 to disable SAP feature on Function menu, if
Function menu is available.
096 - DEF. ASR RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings below.
Set to 0 "Set By System".
Set to I for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 3 for Horizon
Set to 4 for Zoom I
Set to 5 for Zoom 2
099 - BACK LIGHTING
Sets the TV screen brightness at power up, see settings
below.
Default setting value is 255.
1 - 100 Static Backlighting.
(1 = Dimmest picture, 100 = Brightest picture.)
101 - 200 Dynamic Backlighting.
(101 = Dimmest picture, 200 = Brightest picture.)
201 Automatic Static Backlighting
202 Automatic Dynamic Backlighting
Set to between 101 and 200, TV automatically controls
backlighting depending upon the picture level of the cur-
rent program.
Set to 201, TV automatically controls backlighting
depending upon external spectral sensitivity.
Set to 202, TV automatically controls backlighting
depending upon external spectral sensitivity and picture
level of the current program.
Set to 255, to disable power saving mode.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0=BroadcasL 1 =CATV, 2=HRC, 3=IRC, 4=Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to I for Physical chan-
nel scan.
Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets XX-XX minor start channel number at power up:
0=NTSC. If not 0, number selected is the Minor start
channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to I to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off. See
item 96 Default Aspect Ratio above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to I to load presets to all of the previous item settings.
WARNING: Setting this to I will reload the fac-
tory defaults and clear the channel list includ-
ing erasing any assigned Channel Icons and
custom channel Labels.
118 - POWER SAVING
Default is set to I, power saving mode is enabled.
Set to 0 to disable power saving mode.
01_ Power Saving is only active when TV is in standby
mode.
01_ Power Saving is not available in normal power on mode.
If Power Saving is disabled and TV is in Standby mode with
External card installed: TV can supply 12V (12 Watts) to
External card and Standby power consumption will be nor-
mal.
119 - GEM START CH (Gem Start Channel)
Sets the Gem start channel. Set the channel number that
will provide Gem data to the TV at turn on. Initially the TV
may take several minutes to load program data from AC
power off state.
100