Lincoln Electric US-M1785-LS Datasheet

M A T E R I A L S A F E T Y D A T A S H E E T
Conforms to Hazard Communication Standard 29CFR 1910.1200 Rev. October 1988
Manufacturer/
The Lincoln Electric Company
Supplier:
22801 St. Clair Avenue
Cleveland, OH 44117-1199
(216) 481-8100
I M P O R T A N T !
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal
use of this product are covered by Section V; see it for industrial hygiene information.
CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.
(1) The term "hazardous" in "Hazardous Materials" should be interpreted as a term required and defined in the Hazards Communication
Standard and does not necessarily imply the existence of any hazard. All materials are listed on the TSCA inventory.
Ingredients:
Limestone and/or calcium carbonate
Fluorides (as F)
Silicates and other binders
Quartz
Chromium and chromium alloys or compounds (as Cr)*****
Titanium dioxides (as Ti)*****
Iron
Mineral silicates
Manganese and/or manganese alloys and compounds (as Mn)*****
Iron oxides (as Fe)
Niobium alloys (as Nb)
Aluminum oxide and/or Bauxite*****
Molybdenum alloys (as Mo)
Aluminum and/or aluminum alloys (as Al)*****
Titanium and/or titanium alloys (as Ti)
Silicon and/or silicon alloys and compounds (as Si)
Nickel alloy core wire
Nominal core wire composition
Chromium*****
Molybdenum
Niobium
Nickel*****
Supplemental Information:
is 10 milligrams per cubic meter. PEL value for iron oxide is 10 milligrams per
cubic meter. TLV value for iron oxide is 5 milligrams per cubic meter.
(**) As respirable dust.
(*****) Subject to the reporting requirements of Sections 311, 312, and 313 of
the Emergency Planning and Community Right-to-Know Act of 1986
and of 40CFR 370 and 372.
(#) Crystalline silica (quartz) is on the IARC (International Agency for
Research on Cancer) and NTP (National Toxicology Program) lists as
posing a carcinogenic risk to humans.
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section VI.
Product is inert, no special handling or spill procedures required. Not regulated by DOT.
Rev 11/06b
Date:
Trade Name:
Sizes:
Supersedes:
For Welding Consumables and Related Products
SECTION I - IDENTIFICATION
SECTION II - HAZARDOUS MATERIAL (1)
(*) Not listed. Nuisance value maximum
SECTION III - HAZARD DATA
11/5/06
MSDS No.:
Blue Max NiCro 60/20
All
2/1/04
Product Type:
Covered Electrode
AWS ENiCrMo-3
Classification:
CAS No. Wt.%
1317-65-3
7789-75-5
1344-09-8
14808-60-7
7440-47-3
13463-67-7
7439-89-6
1332-58-7
7439-96-5
65996-74-9 < 0.5
7440-03-1 < 0.5
1344-28-1 < 0.5
7439-98-7 < 0.5
7429-90-5 < 0.5
12719-90-3 < 0.5
7440-21-3 < 0.5
7440-47-3 21.5
7439-98-7
7440-03-1
7440-02-0 Bal.
(b) The OSHA PEL for chromium (VI) is 5 micrograms
(0.005 milligrams) per cubic meter. The TLV for water
soluble chromium (VI) is 0.05 milligrams per cubic meter
and the TLV for insoluble chromium (VI) is 0.01
milligrams per cubic meter.
(c) Values are for manganese fume. STEL (Short Term
Exposure Limit) is 3.0 milligrams per cubic meter.
Values are those proposed by OSHA in 1989. Present
PEL is 5.0 milligrams per cubic meter (ceiling value).
(CONTINUED ON SIDE TWO)
US-M1785-LS
TLV PEL
3
mg/m mg/m
10 10 15
5 2.5 2.5
< 5 10* 10*
< 5 #0.05** #0.1**
1 0.5(b) 1.0(b)
1 10 15
0.5 10* 10*
0.5 5** 5**
0.5 0.2 1.0(c)
5 10
10* 10*
10 10
10 10
10 15
10* 10*
10* 10*
70
0.5(b) 1.0(b)
9 10 10
3.5 10 10
1.5 1
3