Byron Home Easy HE-225 Installation Instructions

HE-225 Remote Control
HOME
Timer Kit
easy
RE-INVENTING THE HOME
The HomeEasy remote control Timer allows you to add
the following extra features to your HomeEasy products:
-12 Programmable memory Settings
-Security Mode
-Single and Daily Timer Functions
HOME
easy
300W Dimmer 300W Dimmer 300W Dimmer
-24Hr Timer Display
-30 Metre Wire Free Range
-CR2032/23A Battery (Included)
HOME
HOME easy
easy
300W Dimmer 300W Dimmer 300W Dimmer
Display Functions:
Functions:
1: 12 Programmable Memory Spaces
2: 24Hr Time
3: Timer Setting "On"
4: Timer Setting "Off"
5: Security Mode
6: Timer Mode - Single Timer Setting
7: Timer Mode - Daily Timer Setting
8: Low Battery Warning
9: Unit Code Display
10: Transmission Indicator Signal
Receiver Select
Switch "On" Selected Receiver
Switch "Off" Selected Receiver
Clock Setting
Program Timer/View
Enter
Delete/Pause
Select Up/Down
V1.0 Pairing/Deleting with Remote Control:
Up to Six remote control units can be paired with each receiver socket or
module. To program a socket insert the unit into a plug socket and switch on
the power, now press "Learn" button . The LED will start to flash, now press
the selected "ON" button on the remote control, the LED will stop flashing.
The units are now paired together, you can test this by pressing the selected
"ON/OFF" button
Always refer to the original instruction when using with additional products
Deleting Remote Control:
To delete a remote control that has been paired with a HomeEasy receiver
socket, simply press a "Learn" button. The LED will start to blink; press the "Off"
LCD Display
button on the remote control, the LED will blink twice to confirm that the
remote control has been removed from the receiver sockets memory.
Remote Socket reset:
To delete all the remote control units from the memory of the receiver socket,
hold the "Learn" button for more than 6 seconds, the LED will start to blink
continuously. Press the learn button again, the LED will blink twice to confirm
the deletion of all remote controls form the receiver memory.
Unit Setting:
The HE-200 Remote Control Timer can be paired to 16
separate receiver units, select the unit code by pressing
the unit button.
The HE-200 comes with a preset to Group code A. When
using additional remote control timers you will need to
select a new group code.
To select a new group code, remove the battery cover and
using a small screw driver, rotate the group dial to a new
setting e.g. Group B
Learn Button
Dimming Receiver Sockets HE220:
To dim a compatible receiver socket.
1. Select the unit by 2. Press the "On" button and
pressing the "unit" then press "On" again.
button until the Never exceed maximum
load.
correct number is
HE202 Dimmer Socket:
displayed on the
screen. 300W
HE202 Dimmer Socket:
100W
3. The dimmer will start to dim the light unit till it reaches zero, then the
unit will start to increase the light up to the maximum level. To set the
desired level, press the "On" button.
4. Press the "Off" button to switch the receiver unit off.
Changing Batteries:
Remove the battery cover form the back of the remote control.
The HE-200 includes 2 batteries:
LCD Display: 1 x CR2032 -Byron SX100 (Included)
RF Transmission: 1 x 23A - Byron SD100 (Included)
Remove the required battery and replace with new, making sure the
polarity matches the internal markings.
Product Specification:
Remote Control: HE-200 Receiver Socket:
Battery: 3v Cr2032 & 12V 23A HE-202: Dimmer Socket
Range: 30 Metres (Open Distance) Input: 230V ~ 50Hz
Frequency: 433.92MHz Max Load: 300W (Incandescent)
Indoor Use Only Frequency: 433.92MHz
Indoor Use Only
Warning: Never Exceed the Product Specification
K G
I
_
+