Assigning An Individual Midi Channel; Group A Controllers - M-Audio Ozonic User Manual

< The Buttons and Pedal:
MIDI CC Description
0-119 Standard MIDI CC's
120-127 Channel Mode Messages
128 Pitch Bend Range
129 Channel Fine Tune
130 Channel Coarse Tune
131 Channel Pressure
132 RPN Coarse
133 RPN Fine
134 NRPN Coarse
135 NRPN Fine
136 Master Volume GM*
137 Master Pan GM*
138 Master Coarse Tune GM*
139 Master Fine Tune GM*
140 Chorus Mod rate GM2*
141 Chorus Mod Depth GM2*
142 Feedback GM2*
143 Send to Reverb GM2*
144 Pitch Bend
145 Program/Bank Preset
146 MIDI CC (on/off)
147 Note (on/off)
148 Note (on/off toggle)
149 MMC Command**
150 Reverb type GM2 *
151 Reverb time GM2 *
152 Chorus type GM2*
153 MIDI CC Decrement
154 MIDI CC Increment
OFF Controller Off***
* General MIDI SysEx messages
** General MIDI 2 SysEx messages
*** MMC SysEx messages
**** Press "0", and then press the Enter key. Next press the Octave down button.
< Assigning an Individual MIDI Channel
1 Select the controller you want to edit using one of the two methods described earlier.
2 Press the EDIT button, then the CHAN ASGN key. The LCD will show the current channel assignment of the selected controller,
preceded by a "c."
3 Type the MIDI channel number (0-19) you want the controller to send to, using the numerical data entry keys.
4 Press the ENTER key to confirm.
If the controller is assigned to channel 0, it will transmit on the Global Channel. Information about the Global Channel is given in the Basic
Operations of the Ozonic's MIDI Interface section.
Channels 17-19 are used to define Zone Channels 1, 2, and 3, respectively. If a controller is assigned to channels 17-19, it will always
transmit on whichever channel the appropriate Zone is assigned to. For more information on a Zone's channel, please see the Advanced
Programming Functions section.
< Group A Controllers
Note: For information on Group A memory recall, please review the next section.
A Group A controller refers to any controller that can have a different MIDI CC assignment for each Zone. On your Ozonic, such controllers
include the Pitch Bend wheel, Modulation wheel, Aftertouch strip and the pedals. Although the Transport buttons belong to group A, they
are not considered a Group A controller.
In order for the Group A controller to transmit on all Zones, the channel assignment must be set to 0. If a Group A controller is assigned to
any channel other than 0, it will use the relevant Zone channel for output.
Data 1 Data 2
- Toggle Value 2
- Toggle Value 2
- Sensitivity Value
- Tuning Amount
- Tuning Amount
- Pressure Amount
Value RPN LSB
Value RPN LSB
Value NRPN LSB
Value NRPN LSB
- Volume LSB
- Pan LSB
- Tuning LSB
- Tuning LSB
- Mod Rate
- Mod Depth
- Feedback Level
- Reverb Send Level
- Pitch Shift LSB
Program Bank LSB
MIDI CC Button Press Value
Note Velocity Off
Note Velocity Off
- Command select.
- Type
- Time
- Type
MIDI CC Start Value
MIDI CC Start Value
- -
23
Data 3
Value 2
Value 2
-
-
-
-
RPN MSB
RPN MSB
NRPN MSB
NRPN MSB
Volume MSB
Pan MSB
Tuning MSB
Tuning MSB
-
-
-
-
Pitch Shift MSB
Bank MSB
Button Release Value
Velocity On
Velocity On
-
-
-
-
End Value
End Value
-