LG 42LH250H Owner's Manual page 139

Installer Menu
093 -RJP AVAILABLE (Remote Jack Pack Available)
0 = Remote jack pack is not available or disabled.
1 = Legacy Model RJPs: HDMI Mode
Enables RJP when an HDMI cable is inserted into RJP. Video is from
HDMI. Audio stream is expected from HDMI source. If no audio is pre-
sent, no audio will be heard.
2 = Legacy Model RJPs: DVl Mode
Enables RJPwhen an HDMI cable is inserted into RJP.Video is from
HDMI however, Audio is from selected audio source, based on the RJP's
audio hierarchical priority.
5 = Scaler Model RJPs: HDMI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.Video is from
HDMI. Audio stream is expected from HDMI source. If no audio is pre-
sent, no audio will be heard.
6 = Scaler Model RJPs: DVI Mode
Enables RJPwhen an HDMI cable is inserted into RJP.
Video is from HDMI however, Audio is from selected audio source,
based on the RJP's audio hierarchical priority.
Notes:
See Reference section, RJP Input Hierarchy and RJP Models page.
If set to 1, 2, 5 or 6, item 040 Auto Camport is automatically set to O.
Settings 1, 2, 5 and 6 allow the lodge staff to customize each TV's
RJP setup based on customer requirements.
094 - SAP MENU EN (2rid Audio Program)
Set to 1 to enable SAP feature on Function menu, if Function menu is
available.
Set to 0 to disable SAP feature on Function menu, if Function menu is
available.
096 - DEF.ASP.RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings below.
Set to 0 for "Set By System".
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 3 for 'Just Scan'
Set to 4 for Zoom
099 - BACK LIGHTING
Sets the TV screen brightness at power up, see settings below.
Default setting is 200.
I - 100 StaticBacklighting.
(1 = Dimmest picture, 100 = Brightest picture.)
101 - 200 Dynamic Backlighting.
(101 = Dimmest picture, 200 = Brightest picture.) If settings are above
101, the TVautomatically controls backlighting depending upon the
picture level of the current program.
set to 255, to disable power saving mode.
102 - ATSCBAND
Sets up TVto receive different types of incoming signals:
O=Broadcast, I=CATV,2=HRC,3=IRC, 4=Sameas NTSC.
103 - ATSC TUNE MODE
Sets ATSCtuning mode: Default set to 1 for Physical channel scan.
Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets XX-XX minor start channel number at power up: O=NTSC. If not
O,
number selected is the Minor start channel number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to ] to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off. See item 96
Default Aspect Ratio above.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 to load presets to all of the previous item set-
tings.
WARNING: Setting this to 1 will reload the factory defaults
and clear the channel list including erasing any assigned
Channel Icons and custom channel Labels.
118 - Power Saving
Default is set to 3. When TV is in Standby mode, MPI card slot is
powered by Standby power supply and embedded BLAN is not pow-
ered. When TV is in Power On mode, MPI card slot is powered by
main 12V power supply and embedded BLAN is powered. Note, TV
must be powered on in order to communicate with the embedded
BLAN module forconfiguration and control.
1 = MPI card slot Standby mode power provided from Standby
power supply and embedded BLAN is always powered on.
3 = MPI card slot Standby mode power provided from Standby
power supply and embedded BLAN only powered on when TV is
powered on.
7 = MPI card slot Standby mode power provided from Standby
power supply and embedded BLAN always powered off.
206-4118
P A G E 3 1