300mbps wireless n vdsl/adsl modem router (96 pages)
Summary of Contents for TP-Link TD-VG3511
Page 1
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router Rev: 1.0.0 1910010723...
Page 2
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
Safety Information When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N VoIP ADSL2+ Modem Router Model No.: TD-VG3511 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
CONTENTS Package Contents ....................1 Chapter 1. Product Overview...................2 1.1 Overview of the Modem Router ..................2 1.2 Main Features......................... 3 1.3 Panel Layout........................4 1.3.1 The Front Panel ........................4 1.3.2 The Back Panel........................5 Chapter 2. Connecting the Modem Router .............7 2.1 System Requirements ....................
Package Contents The following contents should be found in your package: One TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router One Power Adapter for TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Three RJ11 cables...
150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router. 1.1 Overview of the Modem Router The TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), three RJ11 ports, one USB 2.0 ports Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide There is no device connected to this LAN port. A storage device or printer has connected to the USB port. (USB) Flash The modem router is sending or receiving data over this USB port.
Page 15
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the RESET button for at least 5 seconds. And the Router will reboot to its factory default settings.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC.
• LINE: Connect to the wall jack • PHONE: Connect to the phone set • MODEM: Connect to the ADSL port of the Modem Router TD-VG3511 Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the Modem RouterTD-VG3511.
Page 18
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 2-1...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem RouterTD-VG3511 or connect your adapter to a Hub/Switch which has connected to the Modem Router, you need to configure your PC’s IP address.
Page 20
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3...
Page 21
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically”...
192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
Page 23
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-8 Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
Page 24
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-10 Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct values assigned by your ISP.
Page 25
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-13 Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by your ISP. If you don’t want to configure VoIP function now, leave "Profile Name"...
Page 26
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-15 You will see the Complete screen below, click Finish to complete these settings. Figure 3-16...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the main menu on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Network Choose “Network”, there are many submenus under the main menu. Click any one of them, and...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.4.1 WAN Settings Choose “Network” “WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-2, which describes the WAN port settings and the relevant manipulation to each interface.
Page 30
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-3 4.4.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
Page 31
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-4 ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP.
Page 32
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Default Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by your ISP.
Page 33
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-5 Click Advanced, advanced selections for WAN Service Setup can be shown. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.
Page 34
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Enable IGMP Proxy: IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the Modem Router. The default value is enabled, and if you are not sure, please contact your ISP or just leave it.
Page 35
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive. Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH, and you can leave it as a default setting.
Page 36
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service type on the screen.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-8 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. DNS Server/Secondary DNS Server: Type in your preferred DNS server.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-9 Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.4.2 EWAN Choose “Network” “EWAN”, and you will see the Ethernet WAN Interface screen similar to Figure 4-10.
Page 39
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-10 4.4.2.1 Dynamic IP Select this option, the Modem Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 Dynamic...
Page 40
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-12 4.4.3 Interface Grouping Choose “Network” “Interface Grouping”, you can view all the current groups on this page (shown in Figure 4-13).
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-13 VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-14 Click Save to make the entry effective immediately 4.4.4 LAN Settings Choose “Network” “LAN Settings” menu, and you will see the LAN screen (shown in Figure 4-15). Please configure the parameters for LAN ports according to the descriptions below.
Page 44
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-15 IP Address: You can configure the Modem Router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the Modem Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide • End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses. The End IP Address must be smaller than 192.168.1.254. The default End IP Address is 192.168.1.199.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-17 Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the Modem Router. PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the •...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-18 DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings.
Page 48
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-19 Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.2 or greater, but...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: To use the DHCP server function of the Modem Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-21 MAC Address: The MAC address of the PC for which you want to reserve an IP address. IP Address: The IP address reserved for the PC by the Modem Router.
Page 51
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-23 To add a vendor class: Click the Add New button. Then Figure 4-24 will pop up. Enter parameters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry: Click the Edit in the entry you want to modify.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.6 Wireless Choose “Wireless”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.
Page 53
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. Mode Select the desired mode.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide SSID (to be bridged): The SSID of the AP your Modem Router is going to connect to as a client. You can also use the search function to select the SSID to join.
Page 55
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WPS: Enable or disable the WPS function here. Current PIN: The current value of the Modem Router's PIN is displayed here. The default PIN of the Modem Router can be found in the label or User Guide.
Page 56
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-27 Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: The WPS LED on the Modem Router will light green for five minutes if the device has been successfully added to the network. The WPS function cannot be configured if the Wireless Function of the Modem Router is disabled.
Page 58
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-30 • Auth Type - you can choose the type for the WEP security on the drop-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide • PSK Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select Enabled or Disabled for this entry on the Status drop-down list. Click the Save button to save this entry. To edit or delete an existing entry: Click the Edit in the entry you want to modify.
Page 61
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-33 Transmit Power: Here you can specify the transmit power of Modem Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.6.6 Wireless Status Choose menu “Wireless” ”Wireless Status”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-34 MAC Address: The connected wireless station's MAC address...
Page 63
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-35 Profile Name: Displays the profile name of the account. Registrar Address: Displays the IP address or domin name of the SIP Registrar server. Phone Number: Displays the phone number of the account.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Display Name: Assign a name for your account. This name is the Caller-ID you want to be displayed on your friend’s display panel, which can let your friend easily know who is calling.
Page 65
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide This section includes Dial Plan List and Forbidden Call. The function allows users to set rules for outgoing calls. 4.7.2.1 Dial Plan List Choose “Voice” “Dial Plan” “Dial Plan List”, you will see the screen similar to Figure 4-37.
Page 66
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. Destination: SIP account can be selected here. As to which one will be finally used, it depends on not only Destination selected here but also Dial Plan Priority configured on Phone Setup page.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-39 Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the numbers you dial. Forbidden: Displays the interface(s) disabled in this plan. Remove: Check the box and then click the Remove button below so that the very plan will be deleted.
Page 68
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-41 Phone Enable: Check the box behind to enable the function. Dial Settings Dial Plan Priority: The parameters configured in the 2 field determine which SIP account to use when making outgoing calls. The following are different options: •...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Warmline Number: Click “View/Set” button to view or set Warmline Number. Answer Settings MWI Mode: Options available are VMWI and CLID. If you don't know, please consult your service provider.
Page 70
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-42 SIP Advanced Setup: Bound Interface Name: Bound Interface decides where to send/receive the VOIP traffic. Easy way to select the interface is to check the location of the SIP server. If it locates some where in the Internet then select Any_WAN.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide facsimile terminals over the Internet or other networks using IP protocols. It will only function when both sites support this feature and are enabled. 4.7.5 Speed Dial Choose “Voice” “Speed Dial”, you will see the screen as shown in Figure 4-43. This section introduces how to configure Speed Dial for your account.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.6 Call Log Choose “Voice” “Call Log”, you will see the screen as shown in Figure 4-46. This function allows you to view call logs and configure call log options.
Page 73
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “Voice” “Call Firewall“ “Mode Setting“, you will see the screen as shown in Figure 4-48.
Page 74
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-50 Enter a number with the length in the range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-49.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.8 USB Voice Mail Choose “Voice” “USB Voice Mail“, you will see the screen as shown in Figure 4-53. USB Voice mail is used to record voice messages when the call is not answered. To use this function, please make sure an external USB hard drive/USB flash disk with configure files has been plugged into the USB port on the Modem Router.
Page 76
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-54 Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operations, you can disable it.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Input the PIN code according to the notification. You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-53.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide File System: The system of the USB drive. Capacity: The storage capacity of the USB driver. Status: Indicates the shared or non-shared status of the volume. Online means volume can be shared, while Offline means volume can not be shared.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Enter the password in the New Password field. Re-enter the password in the Confirm Password field. Click the Set button, and then a new entry will be added in the table.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click Add New Folder in Figure 4-57. Figure 4-58 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed.
Page 81
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-59 Server Status: Indicates the FTP Server's current status. Internet Access: Enable or disable this function. Internet Address: If Internet Access is enabled, WAN IP will be displayed here.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-60 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Server Enable: Select this box to enable this function. Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: Click Add New Folder button, and you will see the screen as shown in Figure 4-62.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.9 Route Settings Choose “Route Settings”, it includes three menus: Default Gateway, Static Route and RIP Settings. The detailed descriptions are provided below. 4.9.1 Default Gateway Choose “Route Settings” “Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-66 Enter the following data: Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select the service you want to use from the Common Service Port list. If the Common Service Port menu does not list the service that you want to use, enter the number of the service port or service port range in the Service Port field.
Page 88
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-70 To add a new rule, follow the steps below. Click the Add New button, the next screen will pop-up as shown in Figure 4-71. Select a common application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automatically filled.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Open Protocol: The protocol used for Incoming Port, either TCP, UDP, or ALL (all protocols supported by the Modem Router). Status: The status of this entry, Enabled means the Port Triggering entry is enabled.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-72 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.11 Parental Control Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in Figure 4-74.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide MAC Address of Current PC: This field displays the MAC address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Add New: Click the Add New button to add a new rule entry. Enable Selected: Click the Enable Selected button to enable the selected rules in the list. Disable Selected: Click the Disable Selected button to disable the selected rules in the list.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: Here displays the description of the host and this description is unique. Address Info: Here displays the information about the host. It can be IP or MAC. Edit: To modify an existing entry.
Page 95
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-79 In Description field, create a unique description for the host (e.g. Host_1). In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-80.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.12.4 Schedule Choose menu “Firewall” → “Schedule”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-82. Figure 4-82 Description: Here displays the description of the schedule and this description is unique.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries in the table. 4.13 Bandwidth Control Choose menu “Bandwidth Control”, and then you can configure the Upstream Bandwidth, Downstream Bandwidth and Bandwidth Control rules for computers in LAN in the next screen.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-85 Click the Save button. 4.14 IP&MAC Binding There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Bound: Check this option to enable ARP binding for a specific device. Edit: To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide IP Address: The assigned IP address of the controlled computer in the LAN. Status: Indicates whether or not the MAC and IP addresses are bound. Load: Load the item to the IP & MAC Binding list.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-90 4.17 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-91 Log Type: By selecting the log type, only logs of this type will be shown. Log Level: By selecting the log level, only logs of this level will be shown.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-93 Time Zone: Select your local time zone from this pull down list. Date: Enter your local date in MM/DD/YY into the right blanks. Time: Enter your local time in HH/MM/SS into the right blanks.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-94 Current User Status: This box displays the information about User Type, User Name, Host IP Address and Host MAC Address. Account Management: Here you can set the account user information about Old Password, New User Name, New Password and Confirm Password.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-95 CWMP: Select enable the CWMP function. Inform: Enable or disable the function. If enabled, the information will be informed to ACS server periodically. Inform Interval: Enter the interval time here.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-96 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs.
The Modem Router will reboot while the upgrading has been finished. Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you...
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide want to use. However, when experiencing problems caused by the Modem Router rather than the configuration, you can try to upgrade the firmware. When you upgrade the Modem Router's firmware, you may lose its current configurations, so before upgrading the firmware please write down some of your customized settings to avoid losing important settings.
Page 109
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-101 Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable. If it is disabled, the function of DoS protection in Security settings will be disabled.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Modem Router’s configuration to its factory default settings? With the Modem Router powered on, press and hold the RESET button on the back panel for 8 to 10 seconds before releasing it.
Page 112
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click Change adapter settings Right-click Local Area Connection Click Properties...
Page 113
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
Page 114
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties...
Page 115
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
Page 116
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows XP OS Go to Start > Control Panel, you will then see the following page. Click Network and Internet Connections Click Network Connections Right-click Local Area Connection Click Properties...
Page 117
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
Page 118
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options...
Page 119
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Modem Router’s factory default settings and reconfigure your Modem Router following the instructions in Login.
Page 120
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup. 4) Then the configuration wizard will pop up and show you how to connect your devices. After that,...
Page 121
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk, enable USB Mail for Line 1 or Line 2. Then click NEXT to continue.
Page 122
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix C: Telephony Features Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available.
Page 124
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient.
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix D: Telephone Operation Code Description Usage Pick up the phone to dial this code and then follow the voice prompts for the operations below: Press 0 to listen to new messages.
Page 126
TD-VG3511 150Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Dial the last incoming Pick up the phone to dial this code. The last incoming number. number will be dialed automatically. Dial the last outgoing Pick up the phone to dial this code. The last outgoing number.
Tel: 444 19 25 (Turkish Service) Tel: AU 1300 87 5465 E-mail: support.tr@tp-link.com NZ 0800 87 5465 Service time: 9:00 AM to 9:00 PM E-mail: support.au@tp-link.com (Australia) 7 days a week support.nz@tp-link.com (New Zealand) Service time: 24hrs, 7 days a week Ukraine...