• To reduce the risk of fire, electrical shock, or motor damage, do not 8 • Operating the Remote Control use a solid-state speed control with this fan. Use only Hunter speed and Mounting the Holder ....... 15 controls, which are solid state.
Page 3
If you want to use an existing fan site, complete the following checklist Fan Support to determine if the site is acceptable and safe for your new Hunter fan. If System you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If install your ceiling fan, go to your fan manual and continue with Section 2 • you are unfamiliar with wiring, use a Installing the Ceiling Plate. qualified electrician. 42222-01 • 05/30/12 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer 3” Wood Screw For Angled Ceilings: Be sure to orient the hanger bracket with the large opening toward the ceiling peak. 42222-01 • 05/30/12 • Hunter Fan Company...
3-5. Align the slot on the ball with the tab on the hanger bracket and place the ball into the hanger bracket. Go to 4 • Wiring the Fan. WARNING: Fan may fall if not assembled as directed in these installation instructions. Slot 42222-01 • 05/30/12 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 42222-01 • 05/30/12 • Hunter Fan Company...
5-2. Align the two keyholes in the canopy with the two partially installed screws. Rotate to engage the screws in the narrow ends of the keyholes and securely tighten the screws. Canopy Hanger Screw Bracket Screw Step 5-2 42222-01 • 05/30/12 • Hunter Fan Company...
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the Step 6-1 (Detail) blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
7 • Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate.
Page 13
Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard Housing or improper operation. Assembly Screw 42222-01 • 05/30/12 • Hunter Fan Company...
Page 14
Exceeding the wattage limit marked on Glass Bowl the MAX wattage sticker affixed to the light socket(s) Cover Plate may result in fire hazard or improper operation. Finial 42222-01 • 05/30/12 • Hunter Fan Company...
You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. Step 8-6 Step 8-7 42222-01 • 05/30/12 • Hunter Fan Company...
To Change Airflow Direction Press the reversing switch on the remote while the fan is running. In cold weather, use upward air flow pattern 42222-01 • 05/30/12 • Hunter Fan Company...
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our website at http://www.HunterFan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 42222-01 • 05/30/12 • Hunter Fan Company...