• To reduce the risk of fire, electrical shock, or motor damage, do not Without a Bowl Light Fixture . . . . . . 12 use a solid-state speed control with this fan . Use only Hunter speed 8 • Operating and Cleaning Your Ceiling controls .
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan . If you cannot check off every item, prepare a new fan site as described on this page .
Page 4
ANSI/NFPA 70 . If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician . 42443-01 • 09/20/10 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease . You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting . The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods .
Parts Guide . Check for any shipping damage to the motor blade irons (if applicable) in sets, or fan blades . If any parts are missing or damaged, contact your Hunter as they were shipped . dealer or call Hunter Technical Support Department at 888-830-1326 .
. Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws . Do not over tighten . Ceiling Plate Flat Washer 3” Wood Steps 2-3 – 2-6 Screw 42443-01 • 09/20/10 • Hunter Fan Company...
3-7 . Raise the fan and align the slots in the canopy with the hooks on Washer the ceiling plate . 3-8 . Place the slots over the hooks to hang the fan . 42443-01 • 09/20/10 • Hunter Fan Company...
. 4-7 . Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box . 42443-01 • 09/20/10 • Hunter Fan Company...
Note: Should you need to remove the trim ring, press firmly on Trim opposite sides of the trim ring directly above the groove in the Ring hanger ball . The tabs will flex out releasing the canopy trim ring . Canopy Screw 42443-01 • 09/20/10 • Hunter Fan Company...
Once they are loosened, finish unscrewing them by hand until they are residue, as they will damage the completely separated from the blade iron . protective Dust Armor on the blades . Carefully remove the blade . 42443-01 • 09/20/10 • Hunter Fan Company...
7 • Completing Your Installation With or Without a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button . This feature gives you the option of installing the fan with OR without the included light fixture .
Page 13
. 7-4 . Install the third housing assembly screw . Steps 7-1 – 7-2 Housing 7-5 . Tighten all three screws securely . Assembly Screw Lower Switch Housing Notch Steps 7-3 - 7-5 42443-01 • 09/20/10 • Hunter Fan Company...
Page 14
Metal Disc pull chains using the breakaway connector . (You may find the breakaway connector on the end of the extra chain . ) Metal Rod Glass Bowl Cover Plate Breakaway Connector Finial 42443-01 • 09/20/10 • Hunter Fan Company...
Page 15
7-17 . Install the switch housing cap and plug button to the lower switch housing . 7-18 . Once you have uninstalled the light fixture, continue with Step 7-1 . Steps 7-14 – 7-16 Male Dummy Terminal Female Dummy Terminal Plug Button Step 7-17 42443-01 • 09/20/10 • Hunter Fan Company...
. 8-6 . The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt . Use a dry or slightly damp lint free cloth to clean the blades .
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our website at http://www . h unterfan . c om . Hunter Fan Company 7130 Goodlett Farms Pkwy . #400 Memphis, Tennessee 38016 42443-01 • 09/20/10 • Hunter Fan Company...